background image

 
 
 
 
 
 
 
 

READ THIS MANUAL CAREFULLY 

 
 
 
 
 

 
 

MOTOCULTIVATOR - MOTORMOWER 

 
 
 

 
 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 

 

 
 
 
 
 
 
 
 

1 - FOREWORD

USE  and  MAINTENANCE  MANUAL 

All right reserved 

 

This manual cannot be either reproduced or released without the 
manufacturer’s prior written consent. 

 

PRINTED IN ITALY

 

 

The machine serial number is printed on the drive box. 

 

 IMPORTANT NOTE 

 
Always mention the machine serial number when calling our technical service or when ordering spare parts. 

 

MARKING 

 

The CE mark is on the right side of the gear-box housing. 

 

 

                             Marking example. 

 
 

 
 
 
 

This symbol is used to highlight an important safety information. If 
this information is ignored, people are in danger either of possible 
injures – even serious ones – or death.

 

IMPORTANT 

This term highlights special precautions to be taken in order not to 
damage the machine. 

 

GB 

12/07

INDEX 

1.

 

FOREWORD   

 

 

 

Pag. 0 

2.

 

IDENTIFICATION AND MARKING 

 

Pag. 0 

3.

 

CONDITIONS AND USING LIMITS 

 

Pag. 1 

4.

 

WARRANTY   

 

 

 

Pag. 1 

5.

 

MACHINE 

STARTING 

 

   Pag. 

6.

 

WARNING AND CONTROL  SIGNS      

               Pag. 2 

7.

 

SAFETY WARNINGS           

 

               Pag. 3-4 

8.

 

ENGINE STARTING      

 

 

Pag. 5 

9.

 

CONTROL DEVICES  USE 

 

                Pag. 6 

10.

 

WORK STARTING                                

 

Pag. 7 

11.

 

RULES FOR A GOOD WORKING                

Pag. 7 

12.

 

MAINTENANCE AND TROUBLES  

 

Pag. 8 

13.

 

TECHNICAL  DATA 

 

                

Pag. 9 

14.

 

ADVICES AND DECLARATION                               Pag. 10   

ENGINE 

Use and maintenance instructions of the engine are 
mentioned in the relevant manual, whose copy is always 
supplied with every machine. 

 

2 – IDENTIFICATION AND MARKING

MTC 601

0

 - 

Summary of Contents for MTC 601














Reviews: