background image

DESCRIPTION

Part#

Qty

Inf Control 208V

14702                   2

Inf Control 240V

12355                   2

Knob Inf Control

12919                   2

Element upper 890W 208V  

*

21103                   2

Element upper 890W 240V  

*

21105                   2

Element assy lower 208V

12618                   1

Element assy lower 240V

12620                   1

Element lower 1200W 208V 

*

12126                   2

Element lower 1185W 240V 

*

21103                   1

Element assy upper 208V

12254                   1

Element assy upper 240V

12266                   1

Motor 208/240V

22743                   1

Speed control 208/240V

21842                   1

Switch, toggle DPST 20a

68117                   1

Knob, speed control

12447                   1

DESCRIPTION

Part#

Qty

Cordset, 6-30P

21221

                  1

Light Pilot 208/240V

51070

                  2

Bearings

22754

                  4

Wire harness kit(wires only)

12933

                  1

Jumper

21358

                  4

Terminal block

21858

                  1

Drive chain 54 links

12412

                  1

32T sprocket assy

21319

                  1

8T sprocket asst

30494

                  1

Front trim, left side

12219

                  1

Legs 1” plastic

12668

                  4

Control panel

12060

                  1

Control panel decal

12061

    1

Savory logo

12523

                  1

Savory lubricant

21720

                  1

PARTS & SERVICE MANUAL for RT-2AR

“Adjustable Range” Toaster

The information found in this Manual
will prove very helpful.  Although the
instructions are easy to follow, all
repair procedures should be carried
out by a qualified Merco/Savory
Certified Service Representative.

The RT-2AR should be placed in the
most convenient location for ease of
cleaning, maintenance, service and
general operation. Careful consider-
ation should be given to avoid drafts,
close proximity to grease or vapor-
producing appliances or high ambient
heat equipment.  Minimum of  ½”
clearance is required for air circula-
tion.  This is assured by the rounded
“acorn” nuts protuding from the sides
and rear.  Overhead clearance from the
top of the toaster should be as much
as possible and sufficient to allow heat
dissipation.

05-02kdl

07155

Summary of Contents for RT-2AR









Reviews: