background image

ATTENTION: With the key out of the ignition, 

disconnect the negative battery terminal 

before installing this product. Ensure that all 

installation connections are secure before 

cycling the ignition to test this product.

NOTE: Refer also to the instructions included 

with the aftermarket radio.

The World’s best kits.

®

 

MetraOnline.com 

© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION 

REV. 10/15/21 INSTBC-DSPX-HD2

I N S TA L L AT I O N I N S T R U C T I O N S

BC-DSPX-HD2

KIT FEATURES

• Saddle Tramp DSP with radio reflash capabilities
•  Reprograms the OE radio to a flat frequency response curve
•  All settings done via the AXXESS DSP XL application
•  BC-9715 pre-wired harness included for ease of installation
•  DSP offers 31 adjustable EQ bands per channel
•  Up to 10 channels of programmable output
•  Fully adjustable crossover

KIT COMPONENTS

•  A) Saddle Tramp DSP  
•  B) BC-9715 Harness  
•  C) Instruction Sheet

 TOOLS REQUIRED

•  Panel removal tool 
•  Phillips screwdriver  
•  Torx screwdrivers
•  Allen wrenches 

TABLE  OF CONTENTS

Fairing Disassembly
  Harley Davidson 

Street Glide, Electra Glide, 

Ultra, 

and 

Limited

 Model 2014-Up .................2  

Harley Davidson Road Glide

 2015-Up ............3

Reflashing the Radio .........................................4-5
Equipment Installation
  Interface Assembly ..........................................6 
  BC-9715 Harness Assembly ...........................7-8 
DSP Setup ..........................................................9-19
Troubleshooting ...................................................20

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Saddle Tramp interface and  
  harness included
Antenna Adapter: Included
Handlebar control interface: Included

Harley-Davidson

 Street Glide, Electra Glide, 

Ultra, and Limited Models 

2014-Up

Road Glide

 

2015-Up

 Non-amplified models only

Visit 

MetraOnline.com

 for more detailed information about the product and up-to-date vehicle 

specific applications

Summary of Contents for Saddle Tramp BC-DSPX-HD2

























Reviews: