background image

Tx22v2 Transmitter

User Information

Tx22v2 is a hand-held wireless transmitter intended to control up to 12 model railway trains. It
has controls for Speed, Direction, Inertia, Lights and Loco selection. Tx22v2 is available in 2
versions: with and without a detent on the throttle control:

the detent version has a mechanical 'click' at the centre of the travel and is intended
for use with DT receivers configured for fwd/rev control on the throttle channel,

the no-detent version is for use with receivers configured for full-range throttle and
separate direction switch. When the Tx22v2 toggle switch is not used for direction, it
is available for controlling auxiliary functions such as LED lights and sound modules.

Technology

Tx22v2 uses the 2.4GHz band which requires no frequency channel control and is very resilient against interference. 
All radio frequency components are contained on the internal Tx2 module. There are no user adjustable parts on this 
module and it should not be modified.

Tx22v2 is compatible with all DSM2 receivers. This includes all Deltang receivers.

Any number of receivers can be bound to your Tx22v2 but only up to twelve, bound to different Selecta positions, 
should normally be switched on at a time to operate them independently. An exception to this rule is multi-headed 
trains – Deltang receivers support features (which required programming setup) to match the speed of separate locos 
in a multi-headed consist.

Range is suitable for indoors and small outdoor sites; the outdoor free-air range to a Deltang receiver is at least 50m. 
Range indoors is affected by building construction materials, furniture, people and receiver installation.

Knob and switch positions are transmitted as separate 'channels' (1-7) which must match the receiver configuration:

throttle:

channel 1

selecta:

channel 2

toggle switch:

channel 3 (up or forward = channel high, down or reverse= channel low)

inertia:

internal use or channel 4 or channel 5 (configurable)

bind button:

channel 5 (none if inertia configured as channel 5) (up = channel high, down = channel low)

Battery

Tx22v2 uses a PP3 9V battery, Alkaline, LiIon or NiMH  The maximum
working voltage of the internal Tx2 module is 10V and there is a protection
diode wired in series with the battery negative lead. This allows the battery
voltage to be up to 10.7V. If the battery voltage is above this value, the
internal regulator will shut down and the transmitter will not operate.

Remove the sliding lid at the bottom rear of the case to insert or replace the
battery. The image shows the orientation. The battery is held in place with a
piece of foam tape attached to the battery compartment lid.

Make sure that the power on/off button is off (up) before) adding or removing
a battery.

The connector will only clip onto the battery one way. TAKE CARE, if force is needed, the connector is probably the 
wrong way round.

On / Off Push Button

Tx22v2 has an illuminated push-button on/off switch. It is best to switch the transmitter on before the receiver.

The LED flickers slightly while an Inertia transition is in progress.

The LED flashes more boldly when Binding.

Tx22v2 User Information
1 of 4

info@micronradiocontrol.co.uk

Summary of Contents for Tx22v2

Page 1: ...all outdoor sites the outdoor free air range to a Deltang receiver is at least 50m Range indoors is affected by building construction materials furniture people and receiver installation Knob and switch positions are transmitted as separate channels 1 7 which must match the receiver configuration throttle channel 1 selecta channel 2 toggle switch channel 3 up or forward channel high down or revers...

Page 2: ...osition The Selecta knob controls channel 2 Bind Button If a receiver has not previously been bound it has to be paired with the transmitter Binding is only required once per receiver 1 Choose the Tx22v2 Selecta switch position for the loco but don t switch the Tx22v2 on yet 2 Put your receiver into Bind mode if a Deltang receiver switch it on and wait 20s for the LED to flash fast 3 Press and hol...

Page 3: ...Rx6 types and Rx47 Method 1 chan 2 and 4 1 switch Tx22v2 on receiver off 2 set the Inertia knob to control channel 4 described above 3 rotate the channel 2 Selecta and channel 4 Inertia knobs fully left or right not centred 4 centre the channel 3 Direction toggle switch 5 put channel 1 Throttle in the off position 6 switch the receiver on 7 the receiver LED will flash rapidly 8 centre the Selecta ...

Page 4: ...ent again to get to 1 and then again to get to 2 press the toggle switch up position A and back to centre to save the LED flash count for the current level and move on to the next program level when all programming levels have been entered the receiver LED will light solid and the receiver will exit programming mode The receiver LED will flash rapidly as the toggle switch is pressed down or up and...

Reviews: