background image

Copyright © 2001 Microtek International, Inc.  http://www.microtek.com
I49-003275 A, December 2001

ScanMaker 9800XL

Installing and Getting Started

Contents

Introduction ............................................................................................................... 2

System Requirements ............................................................................................... 2

Unpacking the Scanner ............................................................................................. 3

Taking a Closer Look ................................................................................................. 3

Unlocking the Scanner .............................................................................................. 4

Shipping scanner ............................................................................................... 4

Installing the Scanner Software ............................................................................... 5

Connecting the Scanner to Your Computer ............................................................. 6

Using the FireWire cable ................................................................................... 6

Using the SCSI cable ......................................................................................... 8

Using the USB cable ......................................................................................... 11

Positioning Reflective Originals ............................................................................. 13

Your First Scan ........................................................................................................ 14

Performing Color Calibration ................................................................................. 16

The color calibration target ............................................................................. 16

Before you calibrate ......................................................................................... 16

Calibrating your target .................................................................................... 17

Loading a profile .............................................................................................. 18

Specifications .......................................................................................................... 20

Additional Documentation in the CD-ROM ........................................................... 20

Trademarks

Microtek

®

, ScanMaker

®

, and

ScanWizard

TM

 Pro are

trademarks or registered
trademarks of Microtek
International,  Inc.
Macintosh

®

 and Apple

®

 are

registered trademarks of
Apple Computer, Inc.
Windows

®

 is a registered

trademark of Microsoft
Corporation. All other
products or name brands
are trademarks of their
respective holders.

Important

Documents you scan may
be protected under
copyright law. The
unauthorized use of such
documents could be a
violation of the rights of the
copyright holder. Microtek
bears no responsibility for
the unauthorized use of
copyrighted materials.

Summary of Contents for ScanMaker 9800XL





















Reviews: