background image

Installation and Service Instructions

Midco

®

 International Inc. 

4140 West Victoria Street
Chicago, Illinois 60646
toll free  866.705.0514
tel 

 773.604.8700

fax 

 866.580.8700

web 

 www.midcointernational.com

e-mail   sales@midcointernational.com

Quality Designed for Proven Performance

Printed in USA

8470 23

•  In the United States, installation must conform with local codes 

or in the absence of local codes, with the National Fuel Gas 
Code, ANSI Z223.1-latest edition available from American 
National Standard Institute. Further reference should be made 
to the recommendation of your fuel supplier.

•  In Canada, installation must conform with local codes or in the 

absence of local codes, with Installation Codes for Gas Burning 
Appliances and Equipment, CGA Standard CAN/CGA 1-B-149.1 
or 2. 

 
•   

WARNING:  Additions, changes, conversions 

and service must be performed by an authorized Midco 
representative, service agency or the fuel supplier. Use 
only MIDCO specifi ed and approved parts.

•  INSTALLER:  Inform and demonstrate to the user the correct 

operation and maintenance of the gas utilization equipment. 
Inform the user of the hazards of storing fl ammable liquids 
and vapors in the vicinity of this gas utilization equipment 
and remove such hazards.  Affi  x this manual and associated 
literature to the burner.

  CODE COMPLIANCE IS THE SOLE 

RESPONSIBILITY OF THE INSTALLER.

•  USER: Retain this manual for future reference. If other than 

routine service or maintenance as described in this manual 
and associated literature is required, contact a qualifi ed service 
agency. DO NOT ATTEMPT REPAIRS. An inadvertent service 
error could result in a dangerous condition. 

            

               WARNING: If the information in these instructions 
       is not followed exactly, a fi re or explosion may result, 
       causing property damage, personal injury or death.

Do not store or use gasoline or other fl ammable vapors and 
liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do not use any  

 

phone in your building.

• 

Immediately phone your gas supplier from another  

 

building. Follow the gas supplier’s instructions. If    
you cannot reach your gas supplier call the fi re    
department.

Installation and service must be performed by a qualifi ed 
installer, service agency or the gas supplier.

SAFETY INFORMATION TERMS:

 The following terms are used to identify hazards, safety precaution of special notations 

and have standard meanings throughout this manual.  They are printed in all capital letters using a bold type face as shown 
below, and preceded by the exclamation mark symbol.  When you see the safety alert symbol and one of the safety information 
terms as shown below, be aware of the hazard potential.
 

DANGER:

 

Identifi es the most serious hazards which will result in severe personal injury or death.

 

WARNING:

 

Signifi es a hazard that could result in personal injury or death.

 

CAUTION: 

Identifi es unsafe practices which would result in minor personal injury or product and  property  

 

 

damage.

BURNER MODEL:   ___________________________________

BILL OF MATERIAL
NUMBER:  

___________________________________

SERIAL NUMBER #: ___________________________________

WIRING DIAGRAM:  ___________________________________

 

FOR SERVICE CONTACT

Name: 

____________________________________________

Address: ____________________________________________

 

____________________________________________

Phone:  ____________________________________________

Date of Installation: ___________________________________

C

O

M PAN

Y

 

R

E

G

IS TER

E

D

 

AVOID ERROR IN PARTS SELECTION. 

 When ordering use complete MIDCO 

Part Number and Description. Furnish Burner Model Number, Bill of Material 
Number and Serial Number (if available) from the specifi cation plate found on the 
product. 

IMPORTANT: 

 Availability of parts as well as specifi cations are subject to change 

without notice. Please consult factory for item availability.

MADE

 in the 

USA

Incinomite J83-DS

    Incinerator Gas Burner

 917

Summary of Contents for Incinomite J83-DS













Reviews: