MinimumRC P40 Q Series Assembly Instructions Manual Download | Manualshive

Page: 1 / 16

background image

P40 Q-Series

Assembly Instructions

Important notification

1.The model is supplied with UFO and 502 glue. UFO is for bonding foam parts, and 502 for
bonding wood, carbon fiber and metal parts. 502 glue will cause serious corrosion to foam parts.

2.Please wait for the glue to dry and solidify in each installation step before the next installation.
3.Please avoid using flame to heat the heat shrinkable tube on the model. Electric iron shall be
used for heating.

4.Please use razor blade to remove the parts from the plate. Do not tear the parts by force.

1
2
3
...
»

Summary of Contents for P40 Q Series

















Reviews:

No comments

Related manuals for P40 Q Series

Brand: Faller Pages: 4

Brand: Uhlenbrock Elektronik Pages: 34

Brand: marklin Pages: 36

THE GHOST HOUSE

Brand: RavensBlight Pages: 10

Pacific Electric 20381

Brand: LGB Pages: 20

Brand: Multiplex Pages: 36

Pennsylvania 6-8-6 Bantam Turbine Steam Freight...

Brand: Rail King Pages: 24

Fishbellied bridge

Brand: Faller Pages: 4

Brand: Fisher-Price Pages: 16

Brand: Black Horse Model Pages: 14

Brand: Bestway Pages: 6

Brand: Walkera Pages: 12

Brand: Jamara Pages: 12

Speedstars Maximum Thrills Raceway 06707

Brand: Playskool Pages: 4

Brand: Hobbytech Pages: 36

Sort & Discover Car

Brand: VTech Baby Pages: 11

Brand: Playskool Pages: 2

Brand: Sparc Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands