INSTALLATION GUIDE
Please record product serial number.
S N
Parker
TM
- Tub Shower
PT516L/R, PT520L/R
-
Parker
TM
- 1 Piece Tub Shower
PT513L/R, PT523L/R
-
Parker
TM
- 3 Piece Tub Shower
The Acrylic Tub Shower was carefully inspected and packed for
shipment. You should check your unit and if there are any
problems, contact your dealer before installation.
Protect the tub shower from dirt and damage by leaving the
polyethylene protective film in place until installation and other
related construction are complete.
IMPORTANT
TOOLS AND MATERIALS REQUIRED
Tools:
Tape Measure, Electric Drill, Drill Bit (3/16”), Level, Hole Saw
and Caulking Gun
Materials:
Mildew Resistant Silicone Bathroom
Caulking, Drywall Screws and Shims
(if required)
.
Assembly and installation of this shower unit requires 2 persons.
To cut plumbing fixture openings on the tub shower unit:
Use correct size hole saw based on selected fixture design.
Cut from the finished side of the unit.
Use masking tape to mask the surrounding surface to prevent
scratches and other damages.
CAUTION
General Installation Notes
Dimensions are clear openings. Refer to specification sheet for
dimensions of shower unit.
The Tub Shower is to fit into formed recess as shown in Figure 1 and 2.
Clear opening is required with the flange outside of the opening: 1 PC -
57 ½” x 88 ½” and 3 PC- 57 ½ ”X84 ½”
Rough- in dimensions:
1PC- 60”x90” and 3PC- 60”x86”
Framing
: Inside dimension of the studded alcove are to be as specified
in Figure 1.
Follow Figure 2 as specified to ensure width is 57 ½” between the 2” x
2” recessed studs.
(See detail view.)
Shimming May Be Required
The unit will rest on the front edge and the two legs at the rear of the
unit. Shims may be required to level the tub to ensure adequate
drainage. Insert the bottom section in the alcove and shim accordingly.
Then remove and assemble as per instructions.
The shower is fastened in place using dry wall screws. Holes are to be
drilled in the flange on both sides and across the top. The holes are to
be drilled by the installer, installation is illustrated in figures 3 and 3A.
If there is a gap at the seam on the front post, then shim the flange as
illustrated in Figure 3B.
NOTICE
FIGURE 1
-
LAYOUT
DIMENSIONS
3 PC FRAME
1 PC FRAME
32 ½
ʺ
825 mm
57 ½
ʺ
1461 mm
60 ½
ʺ
1537 mm
88 ½
ʺ
2248 mm
90
ʺ
2286 mm
8 ½
ʺ
215 mm
17
½
ʺ
445 mm
33 ½
ʺ
851 mm
84 ½
ʺ
2146 mm
86
ʺ
2184 mm
57 ½
ʺ
1461 mm
60 ½
ʺ
1537 mm
8 ½
ʺ
215 mm
17
½
ʺ
445 mm
17
½
ʺ
445 mm
57 ½
ʺ
1461 mm
60 ½
ʺ
1537 mm
8 ½
ʺ
216 mm
2
ʺ
x 4
ʺ
WOOD BLOCK
DRYWALL
2
ʺ
X 2
ʺ
WOOD BLOCK
3/8
ʺ
DRYWALL
SCREW
TUB FLANGE
FIGURE 2
Page 1 - 8
Save manual for future reference.
R0084314, Rev B
