NO
TE
SELECT A NICE, CLEAN, SMOOTH CAMPSITE. SHARP STONES
OR STICKS MAY PUNCTURE THE FLOOR OF YOUR TENT. FACE
THE DOOR OF THE TENT IN THE DESIRED DIRECTION. STAKE
ONE FRONT CORNER OF THE TENT FLOOR. THEN PULL THE
OPPOSITE FRONT CORNER TAUGHT BUT NOT OVERLY TIGHT
AND STAKE THAT CORNER. THEN DO THIS TO THE REAR
CORNERS. THEN ALL STAKES MAY BE DRIVEN THROUGH THE
REMAINING STAKE LOOPS.
SEPARATE ALL ALL THE METAL TENT POLES INTO LIKE POLES
OR INTO COLOR CODED POLE GROUPS. SOME POLES MAY BE
IDENTIFIED BY THE ALPHABET CHARACTER AFFIXED ON THE
POLES.. THE CENTER UPRIGHT POLES WILL BE ADJUSTABLE
AND MATE INTO EACH OTHER.
INSERT ONE RIDGE POLE ASSEMBLY INTO THE CENTER POLE
SLEEVE OF THE TENT. THEN REPEAT THIS BY THREADING THE
OTHER TWO RIDGE POLE ASSEMBLIES THROUGH THE FRONT
AND REAR POLE LOOPS IN THE WHITE ROOF. FASTEN THE
CORNERS WITH THE WEB TIES BUT DO NOT APPLY TOO MUCH
TENSION TO TEAR THE SEAMS.
AFTER ALL THREE OF THE ROOF RIDGE POLES ARE FIXED,
TAKE THE ASSEMBLED TWO CENTER UPRIGHT POLES (WITH
THE UPPER SECTIONS TELESCOPED INTO THE LOWER
ADJUSTABLE, LARGER POLES-SEE ILLUSTRATION ON BACK)
INSERT THE UPPER, SWEDGED OR REDUCED ENDS INTO THE
RIDGE ELBOW POLE. THEN PUSH UP THE CRIER RPM TENT BUT
NOT TOO STRAINED. THE TENT SHOULD STAND EASY AT THE
POINT. FINAL ADJUSTMENT SHOULD COME LATER.
247
SETUP INSTRUCTIONS
SEE BACK FOR FRAME ASSEMBLY DETAIL
AFTER THE CENTER ADJUSTABLE POLES ARE EXTENDED TO HOLD UP
THE CENTER OF THE TENT, WORK ON ERECTING ONE SIDE. PLACE
THE TWO SITE UPRIGHTS INTO THE SIDE ELBOW POLES AND SLIDE
THE LOWER ENDS ALONG THE GROUND TO RAISE THAT WALL. DO NOT
APPLY TOO MUCH PRESSURE THAT MIGHT INJURE THE STAKE AND POLE
LOOPS. THEN, REPEAT THE SAME POLE ASSEMBLY AT THE OTHER SIDE
OF THE TENT.
NOW THE TENT SHOULD BE STANDING RATHER WELL AND MAY NEED
SOME MINOR ADJUSTMENT. FIRST CHECK THE FLOOR. TO SEE THAT
MOST OF THE WRINKLES ARE OUT. YOU MAY HAVE TO ADJUST THE
STAKE LOCATIONS. THEN RAISE THE CENTER UPRIGHT POLES TO APPLY
PRESSURE (BUT NOT TOO MUCH TO STRAIN THE FABRIC OR STAKE
LOOPS OR SLEEVE IN THE ROOF). THEN, ADJUST THE SIDE UPRIGHT
POLES BY SLIDING THE LOWER ENDS TO MAKE THE FRONT AND REAR
WALLS LOOK WELL. PAY ATTENTION TO THE SAME STRAIN WARNINGS
ALREADY MENTIONED. DO NOT APPLY TOO MUCH PRESSURE THAT WILL
CAUSE THE SEAMS OR FABRIC TO TEAR! CAREFULLY REVERSE THESE
STEPS TO DISMANTLE YOUR TENT.
1
5
6
2
3
4
DO NOT LEAVE YOUR TENT IN DIRECT SUNLIGHT FOR
LONGER THAN NECESSARY! THE SUN’S ULTRA VIOLET (UV)
LIGHT DEGRADES PRACTICALLY EVERY SYNTHETIC FABRIC,
MAKING IT WEAK AND FADED. UV DAMAGE IS NOT COVERED
BY OUR GUARANTEE!
SEE BACK FOR FRAME ASSEMBLY DETAIL
FOR ONLINE SUPPORT
treksupport@catoma.com
! CAUTION !
KEEP FIRE AND INFLAMMABLES AWAY FROM TENT • DO NOT LEAVE
CAMPFIRES UNATTENDED • DO NOT USE COMBUSTIBLE HEATERS
OR LANTERNS, ETC. INSIDE AT ANY TIME • DO NOT SPRAY TENT WITH
INSECTICIDE OR REPELLENT NOT SPECIFICALLY RECOMMENDED
FOR SYNTHETIC TENT FABRICS • IF LEAKING OCCURS AT THE SEWN
SEAMS, USE AN APPROVED SEAM SEALER • ALWAYS TAKE DOWN YOUR
TENT WHEN NOT IN USE • PROLONGED EXPOSURE TO SUNLIGHT WILL
DEGRADE THE SYNTHETIC FABRIC • WE ARE NOT RESPONSIBLE • PACK
AWAY YOUR TENT AFTER IT IS THOROUGHLY DRY TO AVOID MILDEW
