32.818-002_EN_10/2017
Quick Install
M26 Allround
Lens Options
M26 Allround
• Mx6 system platform with H.264 support
• Includes MxAnalytics video analysis tools out-of-the-box
• Recording on internal microSD card (SDXC, SDHC installed)
• Audio integrated (microphone and speaker)
• Sensor for temperature and shock detector(*) integrated
• Weatherproof and robust camera housing (IP66, IK10)
Standard Delivery M26
1.2
1.3
1.9
1.10, 1.11, 1.12
1.14
1.8
1.13
1.5
1.4
1.6
1.1
1.7
1.15
Item
Count
Part Name
1.1
1
Camera in weatherproof housing, incl. VarioFlex wall mount
1.2
1
Ceiling mount
1.3
1
Sealing for wall and ceiling mount
1.4
1
Lens, installed (standard M14 or B016)
1.5
2
Lens cover, 1 installed, 1 replacement (not available for lens
B016, cover for B500 not shown, no replacement cover for B500)
1.6
1
Lens wrench B016 (only for D016/N016)
1.7
2
Allen wrench 5 mm, Allen wrench 2.5 mm
1.8
1
Special Ethernet cable 0.5 m/20", installed
1.9
4
Screw caps for stainless steel fastening screws
1.10
4
Stainless steel wood screws 6x50 mm
1.11
4
Stainless steel washers 6.4 mm dia.
1.12
4
Dowel S8
1.13
2
Cable lock with bayonet catch (Ethernet patch cable, MiniUSB)
1.14
1
MicroSD card installed
1.15
1
MiniUSB plug
Allround Outdoor Camera for Ceiling,
Wall and Pole Mounting
MOBOTIX 6MP camera for flexible use in indoor and
outdoor applications, available as complete M26 Allround
(Day or Night) with the lenses MX-B036 to MX-B500 and as
Hemispheric variant (Day or Night) with lens MX-B016.
More Information:
www.mobotix.com > Products > Outdoor Cameras > M26
Removing/Installing the Weatherproof Housing
For certain tasks (e.g., connecting additional wires, exchanging the SD card), you need to remove the weatherproof housing and install it again once
you are finished.
1. Remove the fastening screws at the back
Start by removing the two rubber plugs that
protect the fastening screws. Next, unscrew
the two fastening screws of the weatherproof
housing using the supplied Allen wrench 5 mm
(item 1.7), but do not remove the screws
2. Remove camera from weatherproof housing
Press the camera from the housing by gently
applying pressure on the screws in alternating
fashion from the rear using the long shank of
the Allen wrench. Unscrew the fastening screws
once the camera is free from the housing
3. Complete the tasks
Follow the procedures for the work inside the
housing as described in the M25 Camera Manual
in
Chapter 2, «Installation» (e.g., connecting
additional wires, exchanging the SD card).
4. Insert the camera into the weatherproof housing
Start by inserting the camera into the weath-
erproof housing. Press the camera back into
the housing and take care not to squeeze and
damage any wires inside the housing.
5. Tighten the retaining screws
Affix the camera in the weatherproof housing
using the two retaining screws.
Finally, push in the two rubber plugs that pro-
tect the retaining screws.
Mounting Options of the M26
1. Mounting to a Wall
When installing the M26 on a wall, for example, simply affix the pre-installed
and
VarioFlex wall mount included in the delivery with the four supplied
screws and washers.
The camera can be turned or tilted 180° horizontally and 110° vertically
(from –90° to +20°).
2. Mounting to a Ceiling
By exchanging the wall mount for the separately supplied ceiling mount,
the M26 is ready to be
mounted to ceilings in just a few easy steps thanks
to the VarioFlex system.
The camera can be turned or tilted 360° horizontally and 110° vertically
(from –90° to +20°).
3. Mounting to Poles (With Accessories)
If you want to mount the camera to a pole with a diameter from 60 to 180 mm,
you should consider using the Pole Mount (MX-MH-SecureFlex-ESWS) made
from white powder-coated stainless steel.
Just like when mounting to a wall, the camera can be turned 180°
horizontally and tilted 110° vertically (from –90° to +20°).
–90°
+20°
Mounting to a Wall
360°
Mounting to a Ceiling
M26 B036 – B500
Hemispheric
M26 B016
Connection and Initial Operation of the M26
For information on
connecting the M26, please see the M25 Camera Manual, section «Network and Power Connection, Additional Cables» (PDF,
available on
www.mobotix.com > Support > Manuals).
Please note that the boot options of this camera have changed compared to its predecessor (see
«Boot Options of the M26 on page 1) and the camera
only has one key ("R"). Regarding the rest of the
initial operation of the M26 please see the M25 Camera Manual in Chapter 3, «Initial Operation»
Microphone
Wall Mount
Recording
Weatherproof
housing
Lens and lens
cover
Speaker
Power/Status
Key R
Ethernet
Pressure vent
Retaining screws
USB
Rear (without weatherproof housing)
Installing the M26
1. Drill the holes for the dowels (if required)
Use the drilling template for this step (see
below). Mark the holes for dowels or screws
(blue circles in figure). If required, drill the holes
for the dowels, push them in and cut the cut-
out for the cables. Guide the Ethernet cable
and any other cables that are to be connected
through the cut-out.
2. Connect the cables
If you want to connect additional cables (USB),
remove the weatherproof housing as shown in
Section «Removing/Installing the Weatherproof
Housing», connect the cabling as required and
again install the housing. Plug the pre-installed
Ethernet cable into a network socket (e.g., of
an MX-Overvoltage-Protection-Box).
3. Install the camera
Press the wall/ceiling mount and the wall sealing against the mounting
position and align the holes with the holes for the dowels/screws. Insert
the screws with washers and tighten them using a torque of 0.4 Nm. Finally,
press the white covers onto the screw heads.
Ethernet
USB
Inserting/Exchanging the SD Card
All camera models can use the integrated microSD card (SDHC) to record video data. In order to exchange the microSD card, please proceed as outlined
in the following instruction. For information on reliable SD cards, please see the MOBOTIX website
www.mobotix.com
> Support > MxMedia Library >
Planning in the document MicroSD Card Whitelist for MOBOTIX Cameras.
When replacing the SD card, make sure that recording has been deactivated in the browser (
Admin Menu > Storage > Storage on External File Server /
Flash Device; activate recording again in the same dialog after exchanging the card).
1. Remove the SD Card
Open the camera (see «Removing/Installing the Weather-
proof Housing» ), remove all connectors in the cover of
the inner housing, then remove the cover. Remove the
four screws from the back plate and lift off the back plate.
Gently push on the MicroSD card in the card slot of the
camera. The card is released from the slot and can be
removed from the camera.
2. Insert the SD Card
Push the MicroSD card into the card slot as shown, until
an audible and perceptible click indicates it is in place.
Replace the back plate of the camera housing.
Click!
*:
with firmware version 5.0.1 and higher
