background image

WARNING

This unit contains R-410A high pressure refrigerant. 

Hazards exist that could result in personal injury 

or death. Installation, maintenance, and service 

must only be performed by an HVAC technician 

qualified in R-410A refrigerant and using proper 

tools and equipment. Due to much higher pressure 

of R-410A refrigerant, DO NOT USE service 

equipment or tools designed for refrigerants other 

than R410A.

WARNING

 Improper installation, adjustment, alteration, 

service or maintenance can cause property 

damage, injury or death, and could cause 

exposure to substances which have been 

determined by various state agencies to cause 

cancer, birth defects or other reproductive harm. 

Read the installation, operating and maintenance 

instructions thoroughly before installing or 

servicing this equipment.

IMPORTANT

1.  The use of this manual is specifically intended 

for a qualified installation and service agency. 

A qualified installation and service agency must 

perform all installation and service of these 

appliances.

 2.  ZCV and ZCF units with DX evaporator coils 

contain the refrigerant R-410A. Review the 

R-410A Material Safety Data Sheet (MSDS) for 

hazards and first aid measures.

3.  Refrigerant charging should only be carried out 

by an EPA-certified air conditioning contractor.

AIR14-501.2

5H1035970002 

INSTALLATION AND SERVICE MANUAL

Varsity

TM

 Ceiling Unit Ventilator

Models ZCV and ZCF

December, 2019

Inspection On Arrival

1.  Inspect unit upon arrival. In case of damage, report it 

immediately to transportation company and your local factory 

sales representative.

2.  Check rating plate on unit to verify that power supply meets 

available electric power at the point of installation.

3.  Inspect unit received for conformance with description of 

product ordered (including specifications where applicable).

THIS MANUAL IS THE PROPERTY OF THE OWNER. 

PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB. 

Summary of Contents for Varsity ZCF 1000





















Reviews: