background image

EE

–3189 Office Chair

 

Customer Service 908-368-1025︱www.modwayfurniture.com

 

 

Page  1  of  5 

 

 

 

 

 

 

Thank you for purchasing the 

MODWAY OFFICE CHAIR.

 

Before you start, here are some helpful advice: 

1.  We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step 

instructions. 

2.  Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or 

padded area, in the room that it is intended for. Approximate assembled time: 30 minutes. 

3

Please do not use any tools other than those provided or recommended in these instructions. 

4

Please do not throw away any of the packaging or the instruction until you have checked all the components 

and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe 

and environmentally friendly way. 

5

Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten 

the components from time to time, so please save the tools that have been provided. 

6

Please keep all fitting out of reach of children. 

                                                                                                           

Hardware:

 

A.                                  Bolt M6x20mm        x 8 

B.                                  Bolt M6x35mm        x 4 

C.                                  Flat Washer 18mm x 8 

D.                                  Flat Washer 14mm x 4 

 

E.                                  Allen Wrench            x1 

 

F.                                  Cover                          x4 

Component: 

 

 

 

 

 

 

 

 

 

1  Base x1        2    Cylinder Column x1        3    Control Mechanism x1      4    Seat x1      5    Back Frame x1   

 

6    Left Arm x1    7    Right Arm x1            8    Castor x5            9 

 

Round casing    x1

 

                              8

                              2

                              1

                              9

                              3

                              7

                              5

                              4

                              6

Summary of Contents for EEI-3189






Reviews: