background image

MOD-5804 QUEEN BED

Customer Service 908-368-1025︱www.modway.com

 

Page  1  of  5 

Thank you for purchasing the 

MODWAY QUEEN BED!

Before you start, here are some helpful advice: 
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step

instructions.

2

.

Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or

padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.

3

.

Please do not use any tools other than those provided or recommended in these instructions.

4

.

Please do not throw away any of the packaging or the instruction until you have checked all the components and

hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way. 

5

.

Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the

components from time to time, so please save the tools that have been provided.

6

.

Please keep all fitting out of reach of children.

Hardware:

 

Components:

 

1. Headboard

x1  2. Footboard

x1   

6. Center Plastic Cover

x13      7. Side Plastic Cover

x26  8. Slat

x26 

9. Slat Support       x2   

10. No.10 Leg     x4  11. No. 11 Leg     x4

10

1

3

3

2

11

Bolt M8x50mm      x10 

Bolt M8x25mm      x28 

Bolt M8x20mm      x10 

Flat Washer              x48 

Lock Washer   

    x48 

Screw 25mm     

  x32 

Allen Wrench          x1 

A. 

B. 

C. 

D. 

E. 

F. 

G. 

H.

Screw Driver

x1(Not Included) 

3. Bed Rail

x2    4. Center Rail

x1 

5. Center Support Leg

x3 

Summary of Contents for MOD-5804






Reviews: