background image

Tool Kit for P-Lock Flag Female Terminal 

Doc No: ATS-6382566HM  Release Date: 01-27-13 

UNCONTROLLED COPY

 

Page 1 of 8 

Revision: A 

Revision Date: 01-27-13 

STRIP LENGTH 

INSULATION 

CRIMP 

BEND 

DOWN 

BEND UP 

ROLLING 

CONDUCTOR CRIMP 

TWISTING 

CUT-OFF TAB 

SEAM 

 

 

 

Application Tooling 

Specification Sheet

 

Tool Kit 

Order No. 63825-6670

 

Hand Crimp Tool 

Order No. 63825-6600

 

 

FEATURES 

 

%

 

A full cycle ratcheting hand tool ensures complete crimps 

%

 

Ergonomically designed soft handles 

%

 

Precisely designed crimping profiles with simple contact positioning 

%

 

Easy handling due to outstanding force ratio 

 

Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed 
into the 63816-0200 (110 V) or the 63816-0250 (220 V) Battery Powered Tool. 

 

Many different Tool kits can be used with a single Battery Powered Tool. 

 

This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant. 

 

Separate Punch set for 24 awg wire and separate punch set for 2 x 24 awg wires, one anvil set. 

 

SCOPE 

Products:  2.8 (.110”) P-Lock Flag Terminal 24 AWG and 24 + 24 AWG.

 

Terminal 

Series No. 

Terminal Order No. 

 

Available in Reel form only 

Wire Size 

Insulation Diameter 

Strip Length 

Terminal 

 

AWG 

mm² 

mm 

In. 

mm 

In. 

104441 

104441-9702 

24 

N/A 

1.45-1.55 

.057-.061 

3.40-3.90 

.134-.154 

24 + 24 

N/A 

1.00-1.30 

.039-.051 

The terminals above are reeled parts only.  Customer to cut off terminal from reel: 0.50mm (.020”) maximum

.

 

 Overall insulation OD specification for terminal. 

 

DEFINITION OF TERMS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

TYPE 4C 

Summary of Contents for 63825-6670









Reviews: