Illustration
Location of controls
2 Band Dual Alarm
Clock Radio
CR1910
OPERATING INSTRUCTIONS
Electrical requirements
Check the voltage on the rating plate of your clock radio corresponds with your house
electricity supply which must be A.C. (Alternating current).
For clock radios with a fitted plug.
If the socket outlets in your home are not suitable for the plug supplied with this appliance
the plug should be removed and the appropriate one fitted.
IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST
BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF
ENGAGED INTO A LIVE SOCKET OUTLET.
Should the fuse in the 13 amp plug require changing a 3 amp BS1362 fuse must be fitted.
Battery back-up facility
Your alarm clock radio is equipped with a battery back-up facility.
1
Remove the battery compartment cover (located underneath the unit) by pressing
down and sliding off the battery cover .
2
Insert a battery size 9 volts PP3/6LR61 (Ensure batteries are inserted correctly)
3
Replace the battery compartment cover.
Should a power interruption occur the clock will continue to run, however, time keeping will not be
accurate. The display will be extinguished to conserve battery life but the memory will retain details
of the clock time and alarm settings.
If the optional battery is not installed in case of the AC power failure the display will blink to indicate
the power was interrupted. You will need to reset the clock and alarm.
Battery back-up is designed to operate for a short period only.
If the unit is not to be used for a prolonged period, remove the battery to avoid battery leakage.
In the interests of environmental safety : dispose of batteries safely.
P.2
P.3
P.4
12
Band selector switch
13
Tuning control
14
LED dimmer switch
15
Volume control
16
Speaker
17
FM wire aerial
18
PM indicator
19
AL1 indicator
20
Dial scale
21
AL2 indicator
22
LED clock display
1
Mains lead
2
Time button
3
Alarm selector switch
4
Alarm mode switch
5
Radio on button
6
Off button
7
Sleep button
8
Snooze button
9
Alarm button
10
Slow clock setting button
11
Fast clock setting button
Switching on, and setting the clock time
Before any alarm functions can be used on your alarm clock radio you must first set the
clock to the correct time.
1
Place the unit on a flat surface. Plug the mains plug (1) into the wall socket and switch
on the wall socket.
2
The clock LED display (22) will flash on/off.
3
Press and hold the TIME button (2) and simultaneously hold down the FAST
SETTING button (11). The LED clock display (22) will fast forward the minutes and
hour segments. Release all buttons when the correct time is set.
4
Press and hold the TIME button (2) and simultaneously hold down the SLOW
SETTING button (10) will adjust the clock time slowly.
5
The PM indicator (18) will illuminate to indicate 12.00 midday has been
reached.
Power on and off
The unit must be switched on before the radio can operate.
1
Switch the unit on by pressing the RADIO ON button (5).
2
Press the OFF button (6) to switch off the radio.
Setting the clock alarm time
The alarm function can be set to operate on the following functions: wake up to two different alarm times
which you can choose to use independently or simultaneously. AL1 or AL2 or AL1 + 2.
Set alarm 1
1
Slide the alarm selector switch (3) to the AL1 position.
2
Press and hold the ALARM button (9) and simultaneously hold down the FAST
SETTING button (11). The clock display (22) will fast forward the minutes and hour
segments. Release all buttons when the correct alarm time is reached.
3
Press and hold the ALARM button (9) and simultaneously hold down the SLOW
SETTING button (10) alarm time will adjust slowly.
Set alarm 2
1
Slide the alarm selector switch (3) to the AL2 position.
2
Press and hold the ALARM button (9) and simultaneously hold down the FAST
SETTING button (11). The clock display (22) will fast forward the minutes and hour
segments. Release all buttons when the correct alarm time is reached.
3
Press and hold the ALARM button (9) and simultaneously hold down the SLOW
SETTING button (10) alarm time will adjust slowly.
If set to AL1 + AL2 the alarm will operate at the preset alarm times.
