Australian owned
Australian designed
61 (0)3 9876 0400
sales@motolux.com.au
www.motolux.com.au
Ordering Information
Australia / New Zealand
1.
Pairing the motor to the remote:
Start by selecting the channel that you want to pair the motor with on the remote control.
Next
Insert Paper Clip in
Hole of Motor
for approx. 1 second and the motor will give a jiggle, then on the
Remote
push the
Up Button.
The motor will jiggle to indicate that it is paired.
2.
Check the Direction:
If the direction is correct there is no action required move to
step 3
.
If the direction is wrong,
Push and hold the Stop Button
until you get a Jiggle from the motor then push the
Down Button.
Test the blind and the direction should be correct.
3.
Limit Setting:
TOP LIMIT FIRST
Push and
hold
the button in the Setting Hole on the remote with a Paper Clip until you get a jiggle – now move the blind to
where you would like the Top Limit to be – now push and
hold
the button in the Setting Hole on the remote, you will get a jiggle
Next
Move the blind to where you would like the Bottom Limit to be – now push and
hold
the button in the Setting Hole on the
remote, you will get a jiggle.
Next (very important)
Push and
hold
the button in the Setting Hole on the remote, you will get a jiggle. This has now recorded the limits, please test
the blind.
The above will need to be done for Each Different Motor on Each Different Channel.
1.
On the Remote go to
Blind 1
on
Channel 1
– Push and
Hold
the
Stop
Button until you get a jiggle. Now go to Channel 6 and
push and
hold
the
Up
Button you will get a Jiggle. Blind 1 is now added to Channel 6.
2.
On the Remote go to
Blind 2
on
Channel 2
– Push and
Hold
the
Stop
Button until you get a jiggle. Now go to Channel 6 and
push and
hold
the
Up
Button you will get a jiggle. Blind 2 is now added to Channel 6.
Repeat these steps until you have moved all blinds over to channel 6.
This feature can also be used to transfer motors onto other Remote Controls.
Simple Programming
Resetting a Motor Back to Factory
To Add Multiple Blinds to a Group Channel
PROGRAMMING INSTRUCTIONS 1/2
Firstly you will need something small enough to put in the both the hole in the head of the motor and in the setting hole on
the remote control, a Paper Clip or Jewelers Screwdriver is perfect.
Firstly plug the charger into the small white cable on the end of the motor, plug the charger into a power point and switch
on the power. You will notice the light will turn red on the wall charger, when the light turns green the motor has been fully
charged.
There is a low battery indicator built into the motor, this will start beeping when the motor needs to be recharged. Please let
your customers know that when the motor starts beeping it needs to be recharged before it can be used again.
Should you need to reset a motor back to Factory Settings you will need to push the button inside the hole in the Head of
the Motor Five Times in quick succession
holding
the button in on the Fifth Push, you will get a Double Jiggle indicating the
motor has been reset and all Limits and Pairing have been deleted.
Example: Putting 5 blinds all on Channel Six.
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 2 - 2021
25mm DC RECHARGEABLE BATTERY 1.0Nm MOTOR - 802311012 (MT25-1/30-ES-E)
