□
After use
Storage and maintenance: when the unit is to be stored for a long period, remove the power supply and bit, open the carbon
brush cover and blow out any accumulated carbon brush dust with compressed air, and wipe the exterior clean. Then store the
screwdriver carefully in a dry, dust-free place away from direct sunlight. Store the bit in grease. To ensure continued
serviceability, periodically check and maintain the screwdriver.
Serial No.:
﹍﹍﹍﹍﹍
ASA Industrial Electric Screwdriver User’s Manual
□
Troubleshooting
If the screwdriver does not work properly, check the list below. If you cannot solve the problem do not open the unit. Contact
one of our authorized agents as soon as possible.
(for full-automatic models
－
low volt. DC motor with soft start controller)
□
If the screwdriver does not run
․
Check that the power supply is outputting power.
。
Check that the power supply plug is inserted properly and that output plug terminals No.1 (-) and NO.4 (+)
show 30VDC (approximate) between them. If no output is shown, change the power supply.
。
Check for a open or short circuit in the 6p-6p cord connecting the screwdriver to the power supply. If an open
or short circuit is found change the cord or plug. (use plug type 2G2022(6p) or purchase equivalent type)
。
Check that the fuse is intact. Caution: when changing the fuse, unplug the power supply.
․
Check that the carbon brush is undamaged, that the carbon brush guide cord with the rotor to become too small.
Anyone of these factors could cause the screwdriver to stop rotating or rotate abnormally.
Inspection method: open the carbon brush cover and use a non-conductive insulated rod to gently press the brush. If the
screwdriver resumes rotating, the carbon brush has reached the end of its useful life and must be replaced immediately.
․
Check that the rotation direction switch are working properly. If no ‘click’ is heard when a trigger is depressed,
it is not working and must be replaced. (make sure to perform this check in a quiet place)
□
If the screwdriver is not rotating normally
․
There is a protective circuit within the power supply. Power is only supplied normally from 3 to 5 seconds after
current flow begins.
․
If the motor only runs intermittently during ‘Forward’ operation, try ‘Reverse’ operation, or rotate the anvil
90 degrees until a ‘click’ is heard, then re-attempt ‘Forward’ operation.
․
Long-term use causes the motor’s commutator to wear down. In this case, it must be replaced.
(this repair must be performed by one of our authorized agents)
□
If the bit falls out easily or wobbles
․
check that the bit matches our specifications. If not, change the bit to one that does.
․
If the bit tends to wobble, remove the bit, rotate it 60 or 180 degrees and re-insert it.
□
If the screwdriver does not stop when the selected torque is reached
․
An excessive torque setting can cause the screw to strip the threads, with the result that the clutch does not
activate. Lower the torque to a level that does not cause stripping.
․
Differences in size between the bit tip and screw slot lengths can cause slopping. Change to a suitable bit tip.
․
The brake circuit may be damaged or the sensor switch may have shifted.
(this repair must be performed by one of our authorized agents)
□
Warranty
We provide a one-year free repair service warranty with this product. The warranty is good for one year from the date of
purchase entered on the Product Information Form. The retailer’s stamp must appear on the form to confirm the date. However,
the following circumstances we will charge the user for any parts and labor cost associated with repairs.
□
For repairs involving normal wear to parts including carbon brushes, bits and power cord, and also to the exterior surface.
□
If the screwdriver was connected to a power source of the incorrect voltage.
□
If there was inappropriate use or an attempt to repair the unit by the user.
□
After the period of the guarantee, or if the user cannot present the manual with stamped Product Information Form.
Retailer’s
Stamp
◎
Specifications and design may be changed without notice for improvement(A-4)
□
A Word of Thanks to Our Customers
Thank you for choosing lightweight and powerful electric screwdrivers. In order to insure maximum performance and product
life, please read through this manual before using your screwdriver.
□
Feature
□
Our screwdrivers are designed for use with precision torque locking screws. It can be used for assembly of middle and
large range items such as home appliances, computers furniture and car industry etc.
□
Low vibration, low noise, meets environmental protection demands.
□
Low-voltage electronic braking circuit for precision torque control, low breakdown rate and long product life.
□
Low-voltage DC motor for safety and prevention of electric shocks.
□
Design features separation of screwdriver and control for low repair costs and higher serviceability rate.
□
Switching power supply plugs directly into screwdriver and builds a soft start circuit, provide more accurate torque,
longer motor life and safe operation.
□
Right-angel (90°) head adapter attaches easily to screwdriver for use in small spaces (>60mm), operates smoothly.
(Optional for 1/4" hex shank only)
□
Ergonomically designed exterior reduces work fatigue and increases productivity.
□
Specifications
Model
ASA-6000 ASA-6000PS
ASA-6500 ASA-6500PS
ASA-6800 ASA-6800PS
Power source
30VDC
Torque range
Kgf-cm/lbf-in
2.0-12.0 / 1.7-10.4
4.0-20.0 / 3.5-17.4
5.0-25.0 / 4.3-21.7
Accuracy ±3%
No load speed / rpm
1150
1000
1000
700
Torque setting
Stepless
Machine screw
mm / in
2.0-3.0 / 0.08-0.12
2.6-4.0 / 0.10-0.16
3.0-5.0 / 0.12-0.20
Available
Machine screw
mm / in
2.0-2.6 / 0.08-0.10
2.3-3.5 / 0.09-0.14
2.6-4.0 / 0.10-0.16
Weight g/lb
490 / 1.1
Length mm/in
228 / 9.0
237 / 9.3
228 / 9.0
237 / 9.3
228 / 9.0
237 / 9.3
Available bit shank
5
ψ
/5mm Hex shank
、
1/4’’ Hex shank
Power consumption
30
40
40
Available power supply
APS-30UA
、
APS-30UE
，
APT-65
Clutch impact
Just one time when torque up
□
Outline
(this drawing applies only to 1/4” hex. bit shank screwdrivers)
ASA-6500 1000RPM
INPUT :30VDC 1.0A
Torque:4.0-18.0 Kgf-cm
ψ34
(Egg-shaed)
BONNET
FWD-OFF-REV SW
HANGER
RING
TRIGGER
(POWER SWITCH)
LABEL
TORQUE REGULATING HANDLE
BIT SLIDE SLEEVE
Lever
start
type
