background image

 EV2637-R-00A 

2.5A Single Cell Switch Mode Battery Charger 

with Power Path Management (PPM) 

and 2.4A Boost Current with Trickle Timer

 

 

 

EV2637-R-00A Rev. 1.1   

www.MonolithicPower.com 

1

 

11/13/2017 

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 

Preliminary Specifications Subject to Change 

© 2017 MPS. All Rights Reserved. 

The Future of Analog IC Technology

DESCRIPTION 

The EV2637-R-00A is the evaluation board 
designed to demonstrate the capabilities of 
MPS’ MP2637, a highly-integrated, flexible 
switch-mode battery charge management and 
system power path management device for a 
single-cell Li-ion and Li-Polymer battery used in 
a wide range of portable applications. 
EV2637 uses two operating modes—charge 
mode and boost mode—to allow management 
of system and battery power based on the state 
of the input. 

When input power is present, the board 
charges a single-cell battery with a 
programmable charge current of up to 2.5A.  

In the absence of an input source, the board 
switches to boost mode through the MODE pin 
to power the SYS pins from the battery with a 
current of up to 2.1A. 
The evaluation board provides full-operating-
status indicators to distinguish charge mode 
from boost mode. 
To guarantee safe operation, the EV2637 has 
input-over-voltage protection, battery over-
voltage protection, thermal shutdown, battery-
temperature monitoring, and a programmable 
timer to prevent prolonged charging of a dead 
battery.

 

ELECTRICAL SPECIFICATION 

Parameter Symbol 

Value 

Units

Charge Mode 

Input Voltage Range 

V

IN

 

4.5 – 6 

Charge-Full Voltage   V

BATT Full

  4.2 / 4.35

Charge Current 

I

CHG

 2.5 A 

Input Current Limit 

I

IN LIM

 2.7 A 

Boost Mode

 

Battery Voltage  

V

BATT

 3-4.5 V 

SYS Voltage 
Regulation 

V

SYS

 

5 V 

SYS Output Current 
Limit 

I

SYS

 

2.2 A 

FEATURES

 

  4.5V-to-6V Operating Input Voltage Range 

  Power Management Function Integrated 

Input-Current-Limit and Input –Voltage -
Regulation 

  Up to 2.5A Programmable Charge Current 

  Selectable 4.35V / 4.2V Charge Voltage 

with 0.5% Accuracy 

  Battery Temperature Monitoring 

  Full Operation Indicators 

  Programmable Timer-Back-Up Protection 

 Battery-Reverse-Leakage 

Blocking 

  Reverse-Boost-Operation for Powering 

System 

  Up to 93% 5V Boost Mode Efficiency @ 

2.1A with BATT=4.35V 

 

Up to 2.1A Programmable Output Current 
Limit in Boost Mode 

 

APPLICATIONS 

 Sub-battery Applications 

 Power-bank Applications for Smart-Phone, 

Tablet and Other Portable Devices  

All MPS parts are lead-free and adhere to the RoHS directive.  For MPS green 
status, please visit MPS website under Products, Quality Assurance page.
 “MPS” and “The Future of Analog IC Technology”, are Registered Trademarks 
of Monolithic Power Systems, Inc. 

Summary of Contents for EV2637-R-00A









Reviews: