background image

1

<

變數

 1>

Contents

Contents

Safety Information ...........................................................................................2
Specifications ...................................................................................................3
Rear I/O Panel .................................................................................................6

LAN Port LED Status Table ................................................................................6

Overview of Components ................................................................................7

CPU Socket .........................................................................................................8
DIMM Slots .........................................................................................................9
PCI_E1~3: PCIe Expansion Slots........................................................................9
JFP1, JFP2: Front Panel Connectors ...............................................................10
SATA1~4: SATA 6Gb/s Connectors ...................................................................10
M2_1: M.2 Slot (Key M) .....................................................................................11
ATX_PWR1, CPU_PWR1: Power Connectors ...................................................11
JUSB1~2: USB 2.0 Connectors ........................................................................12
JUSB3: USB 3.1 Gen1 Connector .....................................................................12
CPU_FAN1, SYS_FAN1~2: Fan Connectors .....................................................13
JTPM1: TPM Module Connector.......................................................................14
JCI1: Chassis Intrusion Connector ..................................................................14
JAUD1: Front Audio Connector ........................................................................15
JCOM1: Serial Port Connector .........................................................................15
JLPT1: Parallel Port Connector .......................................................................15
JBAT1: Clear CMOS (Reset BIOS) Jumper .......................................................16
EZ Debug LED: Debug LED indicators .............................................................16
JLED1: RGB LED connector .............................................................................16

BIOS Setup .....................................................................................................17

Entering BIOS Setup.........................................................................................17
Resetting BIOS .................................................................................................18
Updating BIOS ..................................................................................................18

Software Description .....................................................................................19

Installing Windows

®

 7 64-bit/ Windows

®

 10 64-bit ..........................................19

Installing Drivers ..............................................................................................19
Installing Utilities .............................................................................................20

Thank you for purchasing the MSI

®

 

A320M GAMING PRO/ 

B350M GAMING PRO 

motherboard. This User Guide gives 

information about board layout, component overview, BIOS 

setup and software installation.

Summary of Contents for A320M gaming pro





















Reviews: