background image

M.T.H. Electric Trains®

Z-4000 400-Watt Transformer

Operating Instructions

The M.T.H. Z-4000® Transformer is a state-of-the-art UL-approved 400-watt
model railroad hobby transformer. It features a microprocessor-controlled
interface that provides the model railroader unprecedented control over any AC-
powered model locomotive and locomotive sound system. The Z-4000
transformer may be used alone for local control of a model railroad or it can be
paired with a remote control system, such as the M.T.H. Z-4000 Remote Control
System or the M.T.H. DCS Remote Control System. Operators of any AC
powered O, S, or Standard Gauge locomotive, regardless of manufacturer, will
appreciate the power and control features found in the Z-4000 transformer. For
your own safety and that of your equipment, please read the following pages
before beginning to use your Z-4000 Transformer.

CAUTION-ELECTRICALLY
OPERATED PRODUCT:

Not recommended for children under 10
years of age. M.T.H. recommends adult
supervision with children ages 10-16. As
with all electric products, precautions
should be observed during handling and
use to reduce the risk of electric shock.

Summary of Contents for Z-4000















Reviews: