Music Thing Modular TURING MACHINE Mk ii Instructions Manual Download | Manualshive

Page: 1 / 19

background image

April 20th 2016

www.thonk.co.uk

1

TURING MACHINE Mk ii

(APRIL 2016 ONWARDS)

Eurorack DIY Kit

Instructions

Version 1.01

Music Thing Modular Turing
Machine Mkii version

PLEASE DO NOT LINK TO OR REDISTRIBUTE THIS
DOCUMENT WITHOUT PERMISSION FROM THONK

For the most recent version of this
document please visit –

https://www.thonk.co.uk/documents/turing2016/

Refer also to the Music Thing
documentation here -

https://github.com/TomWhitwell/TuringMachine/

For all technical support please create a
Github account and log an issue here -

https://github.com/TomWhitwell/TuringMachine/issues

Chat about the build here –

https://www.muffwiggler.com/forum/viewtopic.php?t=159116

All Thonk kits are sold under our standard Terms and Conditions -

http://www.thonk.co.uk/faq/

DIY INSTRUCTIONS

This document gives detailed instructions that assume you have purchased a
complete Turing Machine kit from

www.thonk.co.uk

after April 2016, it also

assumes no previous knowledge of electronics.

To learn to solder try

https://www.youtube.com/watch?v=IpkkfK937mU

and

the

Adafruit guide to excellent soldering

– http://

bit.ly/1l77tF4

Watch and understand that whole YouTube video! If you’re not achieving the

results shown in the video then you need to buy new tools or seek advice.

You will not end up with a working unit otherwise.

TOOLS REQUIRED

Soldering iron, snipe nose pliers, wire strippers, small flat head screwdriver
and diagonal cutters AKA snips AKA side-cutters. A Digital Multimeter is
always helpful for checking for bad solder joints and continuity. Thonk sell a
range of inexpensive tools here -

http://bit.ly/1jxqF3n

1
2
3
...
»

Summary of Contents for TURING MACHINE Mk ii




















Reviews:

No comments

Related manuals for TURING MACHINE Mk ii

Brand: Waldorf Pages: 91

Brand: Waldorf Pages: 128

Brand: Yamaha Pages: 66

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 217

Brand: Yamaha Pages: 240

Brand: Yamaha Pages: 19

Sequential Prophet-6

Brand: Dave Smith Instruments Pages: 92

Brand: Erica Synths Pages: 20

Brand: Erica Synths Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands