background image

S82 W18717  Gemini Drive

Muskego, Wisconsin 53150

Phone:  (877) 622-2694

Fax:  (888) 679-3319

www.nabcoentrances.com

Part #C-00121 

Rev. 8/25/16

WARNING

• Turn OFF all power to the Automatic Door if a Safety System is not working.

• Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO 

trained technician. Failure to follow these practices may result in serious consequences.

• NEVER leave a Door operating without all Safety detection systems operational.

Model GT 1175 

Electrical Installation Manual

 

**with U30 Microprocessor Controller** 

(with Revision D Software)

120 VAC

LABEL ON U30 CONTROL

AC115V ± 10%

50 / 60 Hz

BLACK (HOT)

SCREW TO HEADER

WHITE (COMMON)

GROUND LUG

MAD

E IN

 JA

PAN

24

-11

32

7

DS-1

50

NA

GY

RO

 TE

CH

ON/OFF

 POWER 

SWITCH

TRANSFORMER

 

A

M

P

5

TB1

NOISE

FILTER

TB2

T1

S1

ZNR2

ZNR1

AUXILIARY 120 VAC

POWER WIRES

(THESE WIRES NORMALLY 

COILED AND TIED UP)

MOTOR/OPERATOR P/N 24-11327

ACTIVATION SIGNAL

OUTPUT SIGNAL

OFF

OFF

ON

ON

FULLY CLOSED

OPENING

FULL OPEN

CLOSING

FULLY CLOSED

OUTPUT: 0 = ELECTRIC STRIKE OUTPUT

OUTPUT TIMER

0  = (DO NOT USE)

1  = (DO NOT USE)

2  = (DO NOT USE)

3  = ELECTRIC STRIKE FUNCTION

U30 ELECTRIC STRIKE OUTPUT SIGNAL

HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER = 3,  ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE

OUTPUT TIMER

1.0 SEC

3 SEC

U30 CONTROL P/N 24-8901-30

POWER SUPPLY P/N 14-11741

GROUND HARNESS

P/N 14-11872

POWER SUPPLY HARNESS

P/N 14-11874

VIOLET

GRAY (OUT A)

TERMINAL ON U30 MAIN HARNESS

P/N 24-11877

WIRING FOR ELECTRIC LOCK ONLY SHOWN

FAIL SECURE LOCK ASSY.

P.N. 22-10522-03

FAIL

SECURE

VIO

GRY

WHT

BLK

1

6

110V

20V

AC 50/60H

z

Microprocessor Controller

248901-  

GYRO TECH

HOLD OPEN

NIGHT

ONE WAY

TWO WAY

MODE

M1

M0

Open

Gnd

Open

Open

Open

Gnd

Gnd

Gnd

Mode SW Usage

Adjustments to the door can only be made

with the NABCO Handy Terminal.

CAUTION

To maintain warranty,repairs must be 

made by authorized NABCO facilities.

Do not disassemble the control box.

There are no user serviceable parts 

inside.

POWE

R

2P

INDICA

TO

RS

61
6B

H

62
BA

POWER

ERROR

MOTOR

12P

No.

WARNING

To protect against risk of

fire

or electric shock,use only the 

certified NABCO power supply.

RELA

TED DEVICE

S

16

P

HANDY TERMINAL

6P

Mode Switch (see Mode SW Usage shown left)

61

7

6B

12VDC+

12VDC-(Common)

Interior Activation

Holding Beam

M0

H

M1

SLS

62

BA

Exterior Activation

Sidelite Presence Sensor

Breakout Detector

1

2

3

4

5

6

7

8

9

10

11

Reduced Opening Switch

No.

FUNCTION [SLIDING DOOR]

7

12VDC-(Common)

OUT.C

OUT.B

OUT.A

N/O

N/C

Common

Contact Output (Class2 Load only)

30V(42.4Vpeak)max.

5Amax.(0-20V), 3.2Amax.(20-30V)

OUT

Auxiliary Output (Open-Collector)

SQ

Sequential Activation

16

15

14

13

12

12VDC-COMMON

Auxiliary Output (Open-Collector)

Sequential Activation

5Amax.(0-20V), 3.2Amax.(20-30V)

30V(42.4Vpeak)max.

Contact Output (Class2 Load only)

FUNCTION [SLIDING DOOR]

REDUCED OPENING SWITCH

Breakout Detector

Sidelite Presence Sensor

Exterior Activation

HOLDING BEAM

INTERIOR ACTIVATION

12VDC-(COMMON)

12VDC+

Mode Switch (see Mode SW Usage shown left)

Common

N/C

N/O

SQ

OUT

OUT.A

OUT.B

OUT.C

7

SYMBOL

BA

62

SLS

M1

H

M0

6B

9DC12V

7

61

12

13

14

15

16

No.

11

10

9

8

7

6

5

4

3

2

1

RE

LAT

ED DEVICES - 16P

1

2

3

4

5

6

7

8

9

10

11

16

15

14

13

12

1

2

3

4

5

6

7

8

9

10

11

16

15

14

13

12

SYMBOL

9DC12V

Summary of Contents for GYRO TECH GT-1175


































Reviews: