Thank you for purchasing the Ultra-Precision, High-Speed Brushless Motor Spindle " HES510 ". The HES510
Brushless Motor Spindle is designed for use on machining centers without rotating the machine's main spindle, for
small diameter drilling and milling. The E3000 CONTROLLER and Air Line Kit are rquired to drive this Brushless
Motor Spindle. Read this and all the associated component Operation Manuals carefully before use. Always keep
this Operation Manual in a place where a user can referred to for reference at any time.
Ultra-Precision, High-Speed Brushless Motor Spindle
HES510
OPERATION MANUAL
OM-K0480E 003
DANGER
Do not rotate the machining center's main spindle with the HES Brushless Motor Spindle installed.
Rotating the machining center's main spindle with the HES Brushless Motor Spindle installed
can cause the motor cord to become tangled and pull the control unit off it is mounting. This may
cause lead to a big accident.
1
. CAUTIONS FOR HANDLING AND OPERATION
■
Read these warnings and cautions carefully and only use in the manner intended.
■
These warnings and cautions are intended to avoid potential hazards that could result in personal injury to the
operator or damage to the device. These are classi
¿
ed as follows in accordance with the seriousness of the risk.
Class
Degree of Risk
DANGER
Existence of a hazard that could result in personal death or serious
injury, if the safety precautions are not fo.
WARNING
A safety hazard could result in bodily injury or damage to the device if
the safety instructions are not properly followed.
C A U T I O N
A hazard that could result in light or moderate bodily injury or damage
to the device if the safety instructions are not followed.
①
NAKANISHI product's are intended for use by trained, knowledgeable, highly experienced
professionals only.
②
This Brushless Motor Spindle is not a hand tool. It is designed to be used install this Brushless
Motor Spindle to the machining center's machines or milling machine machines.
③
Do not touch the cutting tool while it is running. It is very dangerous.
④
Wear safety glasses, dust mask, and use a protective cover around the HES Brushless Motor
Spindle whenever the HES Brushless Motor Spindle is rotating.
⑤
Never connect, disconnect or touch the Power Cord Plug or Motor Cord Plug with wet hands.
This may cause an electric shock.
⑥
Never operate or handle the HES Brushless Motor Spindle until you have thoroughly read the
Operation Manuals and safe operation has been con
¿
rmed.
1
）
To prevent injuries / damages, check the HES Brushless Motor Spindle and cutting tool for
proper installation, before operating the HES Brushless Motor Spindle.
2
）
Before disconnecting the HES Brushless Motor Spindle, always turn the control power off
and turn the compressed air supply to the CONTROLLER off. Then it is safe to remove the
HES Brushless Motor Spindle.
⑦
When installing a HES Brushless Motor Spindle to a
¿
xed base, make sure the
¿
xed base is
grounded in order to avoid the risk of an electric shock.
⑧
When installing a tool, tighten the collet chuck correctly and check again the collet chuck and
chuck nut before use. Do not over-tighten the collet chuck. This may cause damage to the HES
Brushless Motor Spindle.
⑨
Do not use bent, broken, chipped, out of round or sub-standard tools, as this may cause them
to shatter or explode. Tools with fractures or a bent shank will cause injury to the operator.
When using a new tool, rotate it in a low speed and increase speed gradually for safety.
⑩
Do not exceed the maximum recommended allowable tool speed. For your safety, use speeds
below the maximum allowable speed.
⑪
Do not apply excessive force. This may cause tool slippage, tool damage, injury to the operator
or loss of concentricity and precision.
WARNING
①
Do not drop or hit this HES Brushless Motor Spindle, as shock can damage to the internal
components.
②
Be sure to clean the collet chuck and chuck nut, the inside of the spindle before replacing the
tool. If ground particles or metal chips stick to the inside of spindle or the collet chuck, damage
to the collet chuck or spindle can occur due to the loss of precision.
③
When cleaning a HES Brushless Motor Spindle, stop the HES510 Brushless Motor Spindle and
remove debris with a soft brush or a cloth. Do not blow air into the dust proof cover area (refer
to section " 6 - 2 Outside View ") with compressed air as foreign particles or cutting debris
may get into the ball bearing.
④
Always clean the tool shank before installing the tool in the spindle.
⑤
Be sure to drain moisture and condensation from the Air Line Kit (air
¿
lter bowl) regularly to
avoid moisture being carried to the HES Brushless Motor Spindle. This may cause damage to
the HES Brushless Motor Spindle.
⑥
Check to make sure the HES Brushless Motor Spindle is properly and securely mounted in the
machine's quill prior to use. If the HES Brushless Motor Spindle is not properly aligned or there
is excessive play, do not use the HES Brushless Motor Spindle until this situation is corrected.
⑦
When sizing the correct collet chuck size to the tool shank diameter, a tolerance of + 0
〜
- 0.01mm
is strongly recommended. A tool shank within the + 0
〜
- 0.1mm range is mountable, however,
this may cause poor concentricity and or insuf
¿
cient tool shank gripping force.
⑧
Select suitable products or tools for all applications. Do not exceed the capabilities of the HES
Brushless Motor Spindle or tools.
⑨
Do not stop the supply cooling air for motor during operation of the machine.
Removing the air pressure from the HES Brushless Motor Spindle causes a loss of purging,
allowing the HES Brushless Motor Spindle to ingest coolant. This will cause damage to the
HES Brushless Motor Spindle.
⑩
Carefully direct coolant spray to the tool. Do not spray directly on the HES Brushless Motor
Spindle body. If large amount splay directly on the HES Brushless Motor Spindle, it may cause
excess load of the motor rotation with loss of durability to the HES Brushless Motor Spindle.
⑪
Stop working immediately when abnormal rotation or unusual vibration are observed.
Immediately, please check the content of section " 13. TROUBLESHOOTING ".
⑫
Always check if the tool, collet chuck, chuck nut, connection hose and air hose for damaged
before and after operating.
⑬
Always check if the tool, collet chuck, chuck nut, connection hose and air hose for damaged
before and after operating.
⑭
After installation, repair, initial operation, or long periods of non operation, please refer to
section " 12. BREAK-IN PROCEDURE " detailed in Table 2. When checking the spindle, no
vibration or unusual sound should be observed during rotation.
⑮
Do not disassemble, modify or attempt to repair this HES Brushless Motor Spindle. Additional
damage will occur to the internal components. Service must be performed by NSK NAKANISHI
or an authorized service center.
⑯
When using this HES Brushless Motor Spindle for mass production, please consider the purchase
of an additional HES Brushless Motor Spindle to be used as a back-up in case of emergency.
⑰
Securely connect the compressor supply connection hose and the air hose to the Air Line Kit
and the HES Brushless Motor Spindle to avoid accidental disconnection during use.
CAUTION
Table
1. Packing List Contents
When opening the package, check if it includes all items listed in " Table.1 Packing List Contents ".
In the event of any shortage, please contact either Nakanishi (see the " 4. CONTACT US " section) or your local
dealer.
2
. BASIC PACKAGE
Brushless Motor Spindle
・・
1pc.
* Figure is HES510 - BT30
Collet Chuck
ȭ
4.0mm
(CHK - 4.0)
・・
1pc.
(For U.S. market
･･
ȭ
3.175mm
(CHK - 3.175))
Chuck Nut (K - 265)
・・
1pc.
Wrench (12
×
14)
・・
2pcs.
Electric Connector Cap
・・
1pc.
Air Cap
・・
1pc.
Lock Bar
・・
1pc.
Spiral Tube
・・
1pc.
Ring
・・
1pc.
Plastic Tie (Repeat Type
）
・・
1pc.
Plastic Tie
・・
3pcs.
Plastic Tie
・・
1pc.
Inspection Card
・・
1pc.
Operation Manual
・・
1set
* The Collet Chuck, Chuck Nut, Electric Connector Cap and Air Cap are attached to the Brushless Motor Spindle.
12
14
3
. WARRANTY
We provide a limited warranty for our products. We will repair or replace the products if the cause of failure is due
to the following manufactures defects. Please contact us or your local distributor for details.
①
Defect in manufacturing.
②
Any shortage of components in the package.
③
Where damaged components are found when initially opening the package.
(This shall not apply if the damage was caused by the negligence of a customer)
4
. CONTACT US
For your safety and convenience when purchasing our products, we welcome your questions.
If you have any questions about operation, maintenance and repair of the product, please contact us.
Company Name
Business Hours
U.S. Toll Free No.
Telephone No.
Fax No.
Web Address
:
Industrial Div.
: 8:30am to 17:00pm (CST)
(closed Saturday, Sunday and Public Holidays)
: 800-585-4675
: 847-843-7664
: 847-843-7622
: www.nskamericacorp.com
Contact Us
Contact Us
For U.S. Market
Company Name
Business Hours
Telephone No.
Fax No.
Web Address
:
Industrial Div.
: 8:00am to 17:00pm
(closed Saturday, Sunday and Public Holidays)
: +49 619677606 57
: +49 619677606 29
: www.germany.nsk-dental.com/
For Europe Market
Company Name
Business Hours
Telephone No.
Web Address
:
: 8:00am to 17:00pm
(closed Saturday, Sunday and Public Holidays)
: +81 (0) 289-64-3520
: webmaster-ie@nsk-nakanishi.co.jp
For Other Markets
①
Small diameter drilling and milling which is very dif
¿
cult with large machines can easily be achieved with the
HES Brushless Motor Spindle.
②
Use of a high-performance brushless DC motor and ceramic bearings in the spindle makes the HES Brushless
Motor Spindle extremely accurate and durable.
③
Low vibration, low noise and low heat generation dramatically extends cutting tool life.
④
Wide speed range from 5,000 ~ 50,000 min
-1
(rpm) makes extremely precise work possible.
⑤
A wide variety of Shank Types are available. (BT 30, NT30, BT40, NT40, BT50, NT50, HSK A63, HSK A100,
CAT40, CAT50, IT40, IT50, ST32, R8)
⑥
Various sizes of collet chucks are available CHK 0.5mm - 6.35mm. Standard collet chuck is CHK 4.0mm or
CHK 3.175mm (For U.S. market CHK 3.175mm).
5
. FEATURES
6 - 1 Speci
¿
cations
6
. SPECIFICATIONS AND DIMENSIONS
Model
HES510
Rotation speed
5,000 - 50,000min
-1
(rpm)
Spindle Accuracy
Within 1
ȝ
m
Shank types
BT 30, NT30, BT40, NT40, BT50, NT50, HSK A63,
HSK A100, CAT40, CAT50, IT40, IT50, ST32, R8
Max. Output
340W
Weight
BT30
Motor Cord and Air Hose
2.2kg
425g
Noise Level at 1m distance
Less than 70 dB
Collet Chuck (CHK -
□□
)
ȭ
0.5mm -
ȭ
6.0mmin 0.1mm increments
ȭ
2.35mm,
ȭ
3.175mm,
ȭ
6.35mm.
Motor Cord (icluding Air Hose) *Note
4m, 6m, 8m
Chuck nut
K - 265
<Options>
*Note
：
Motor Cord is sold separately.
Please select the suitable motor cord length for your application.
6 - 2 Outside View
Fig. 1 HES510 - BT30
48.4
ȭ
40
ȭ
63
ȭ
29.6
(213.5)
(94.9)
(165.1)
(17.4)
ȭ
15.9
(70.2)
24
40
※
45°
M8 x 1.25
BT30
60°
ȭ
4 Air Hose
Motor Cord
39.6
23.6
(70.2)
(17.4)
(164.7)
(94.5)
(233.1)
68.4
ȭ
40
ȭ
63
ȭ
29.6
ȭ
15.9
※
45°
NT30
60°
M8 x 1.25
ȭ
4 Air Hose
Motor Cord
Fig. 2 HES510 - NT30
䃥
63
(215.5)
(17.4)
65.4
(150.1)
(79.9)
(70.2)
27.1
※
BT40
ȭ
40
ȭ
29.6
ȭ
15.9
M8 x 1.25
60°
Motor Cord
ȭ
4 Air Hose
(70.2)
(79.5)
(149.7)
93.4
(17.4)
(243.1)
24.6
䃥
63
※
M8 x 1.25
60°
ȭ
40
ȭ
29.6
ȭ
15.9
NT40
ȭ
4 Air Hose
Motor Cord
Fig. 3 HES510 - BT40
Fig. 4 HES510 - NT40
(160.1)
101.8
(17.4)
(89.9)
(70.2)
(261.9)
10.5
䃥
100
䃥
63
※
M8 x 1.25
60°
ȭ
40
ȭ
29.6
ȭ
15.9
BT50
ȭ
4 Air Hose
Motor Cord
(70.2)
(90.1)
(160.3)
126.8
(17.4)
(287.1)
30.2
䃥
100
䃥
63
※
M8 x 1.25
60°
ȭ
40
ȭ
29.6
ȭ
15.9
NT50
ȭ
4 Air Hose
Motor Cord
Fig. 5 HES510 - BT50
Fig. 6 HES510 - NT50
32
7.5
(219.1)
(116.9)
(187.1)
(17.4)
(70.2)
䃥
63
䃥
63
※
M8 x 1.25
60
°
ȭ
40
ȭ
29.6
ȭ
15.9
HSK A63
ȭ
4 Air Hose
Motor Cord
50
8.5
(70.2)
(17.4)
(197.1)
(126.9)
(247.1)
䃥
100
䃥
63
※
M8 x 1.25
60
°
ȭ
40
ȭ
29.6
ȭ
15.9
HSK A100
ȭ
4 Air Hose
Motor Cord
Fig. 7 HES510 - HSK A63
Fig. 8 HES510 - HSK A100
68.25
(238.55)
(100.1)
(170.3)
(17.4)
(70.2)
䃥
63.5
※
CAT40
ȭ
40
ȭ
29.6
ȭ
15.9
60
°
Motor Cord
ȭ
4 Air Hose
101.6
(261.9)
(90.1)
(160.3)
(17.4)
(70.2)
䃥
98.43
※
CAT50
ȭ
40
ȭ
29.6
ȭ
15.9
60°
Motor Cord
ȭ
4 Air Hose
Fig. 9 HES510 - CAT40
Fig. 10 HES510 - CAT50
68.4
ȭ
63.55
(219.1)
(100.1)
(170.3)
(17.4)
(70.2)
※
IT40
ȭ
40
ȭ
29.6
ȭ
15.9
60°
Motor Cord
ȭ
4 Air Hose
101.75
(262.05)
(90.1)
(160.3)
(17.4)
(70.2)
䃥
97.5
※
IT50
ȭ
40
ȭ
29.6
ȭ
15.9
60°
Motor Cord
ȭ
4 Air Hose
Fig. 11 HES510 - IT40
Fig. 12 HES510 - IT50
22
38
(60)
(163.1)
(223.1)
(17.4)
(70.2)
(92.9)
䃥
32
䃥
63
※
ȭ
40
ȭ
29.6
ȭ
15.9
ST32
45°
M8 x 1.25
ȭ
4 Air Hose
Motor Cord
25.3
41.3
(101.6)
(166.4)
(268)
(17.4)
(70.2)
(96.2)
䃥
63
※
䃥
31.75
ȭ
40
ȭ
29.6
ȭ
15.9
R8
45°
M8 x 1.25
60°
ȭ
4 Air Hose
Motor Cord
Fig. 13 HES510 - ST32
Fig. 14 HES510 - R8
※：
Dust Proof Cover Area
ྲྀᢅㄝ᫂᭩
OPERATION MANUAL
᳨ᰝᡂ⦼⾲
Inspection Card
