background image

FRENCH PG. 37

W415-1789 / C / 01.29.19

ADD MANUAL TITLE 

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • hearth@napoleon.com

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS: 

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER: 

Leave this manual with the appliance

CONSUMER: 

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA / 

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other 
fl ammable vapors and liquids in the vicinity of 
this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

:

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not 

use any phone in your building.

•  Immediately call your gas supplier from a 

neighbour’s phone. Follow the gas    
supplier’s   instructions.

•  If you cannot reach your gas supplier, call 

the fi re department.

- Installation and service must be 
performed by a qualifi ed installer, service 
agency, or the supplier.

This appliance may be installed in an aftermarket, 
permanently located, manufactured home (USA 
only) or mobile home, where not prohibited by 
local codes.

This appliance is only for use with the type of gas  
indicated on the rating plate. This appliance is 
not convertible for use with other gases, unless 
a certifi ed kit is used. 

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 
could result in serious injury, death, or 
property damage.

WARNING

!

ENGLISH 

$10.00

FOR INDOOR USE ONLY

IF INSTAL OPERATION, ADD SERIAL 

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE 

BARCODE LABEL ON THE OWNER’S MANUAL”

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

These installation instructions MUST be used in 
conjunction with the Vector™, Luxuria™, and  
Dynamic Heat Control™ installation manuals.

FOR USE WITH VECTOR™ 

(with DHC™ installed)  

& LUXURIA™ MODELS ONLY

DHCP-BK / DHCP-EK / DHCP-HK

INSTALLATION AND 

OPERATION MANUAL

ENSURE TO ORDER CORRECT KITS. 

SEE INSIDE FOR DETAILS.

LV38N/P-1 / LV38N/P2-1 / LV50N/P-2 / LV50N/P2-2 / 

LV62N/P / LV62N/P2 / LV74N / LV74N2

LVX38N/P / LVX38N/P2 / LVX50N/P / LVX50N/P2 / 

LVX62N/P / LVX62N/P2 / LVX74N / LVX74N2

DHCP-BK & 

DHCP-EK Illustrated

Summary of Contents for DYNAMIC HEAT CONTROL PLUS Series









































































Reviews: