National Instruments 9212 Calibration Procedure Download

Page: 1 / 16

CALIBRATION PROCEDURE

NI 9212

This document contains the verification

and adjustment procedures for the NI 9212. For more

information about calibration solutions, visit

ni.com/calibration

Note

Refer to the

NI TB-9212 Calibration Procedure

ni.com/manuals

for

instructions on calibrating the NI TB-9212.

Contents

Software.................................................................................................................................... 2
Documentation.......................................................................................................................... 2
Test Equipment......................................................................................................................... 3

Connecting the NI 9212.................................................................................................... 4

Test Conditions......................................................................................................................... 5
Initial Setup............................................................................................................................... 5
Verification............................................................................................................................... 6

Voltage Verification ......................................................................................................... 6
CJC Verification ............................................................................................................... 8

Adjustment................................................................................................................................ 11

Voltage Adjustment.......................................................................................................... 11
CJC Adjustment................................................................................................................ 12

Summary of Contents for 9212

















Search results

Summary of Contents for 9212

Reviews:

Related manuals for 9212

Brands by name

Popular brands

National Instruments 9212, Calibration Procedure

Search results

Summary of Contents for 9212

Reviews:

Related manuals for 9212

Brands by name

Popular brands