background image

 

ALGO® 5 Newborn Hearing Screener Service Manual 
P/N 000995 Rev.A

 

 1 

 

 
ALGO 5 Installation and Assembly Instructions 

 

1. Preparation 

 
 

Examine the shipping containers carefully upon receipt.  If any of the boxex are damaged or 
the packing materials show signs of stress, notify the carrier and keep the shipping materials 
for the carrier’s inspection. 
 
The ALGO 5 includes these items packaged and shipped separately in 4 boxes::   

 

  Cart base with Isolation Transformer 

  Cart column (with cable guide protective covers included but not installed) 

  Panel PC with Panel PC power supply 

  Accessories box: keyboard, DSP Box, Preamp 5, ATA 5 cable, Sample Pack, label 

printer, and accessories pack: Equipment Check Kit, USB Cable, two PCA 5 cables, 
CD, power cord, and documentation package 

  Optional items packaged separately:  Barcode scanner, LAN Isolator, and page 

printer.  

 

Note: 

Save shipping boxes and packing foam in the event that the screening module 
must be returned to the manufacturer. 

 

Required Tools 

 

T-handle allen wrench, 3/16” (supplied, in Cart Base packaging) 

 

90 degree allen wrench, 1/8” and 5/32” (supplied, in Cart Column packaging) 

 

7/16” standard wrench or adjustable crescent wrench (not supplied) 

 Phillips 

screwdriver 

(not 

supplied) 

 

Hardware Supplied 

  Socket head screws (#1/4-20 x 1 1/4”) with lock washers & flat washers (4, in Cart 

Base packaging)  

  KEP nuts (#1/4-20) – (2, in Cart Base packaging) 

  Socket head cap screws (#10-32 x 1/2” SHCS) -  (4, in Cart Column packaging) 

  Pan head screws (#10-32 x 3/8” PHMS) -  (4, packaged separately, taped to DSP 

bracket on Cart Column) 

  Post cap plate – (1, in Cart Column packaging)

 

  Button head socket cap screws (#1/4-20 x 3/8” BHSCS) – (4, packaged with post cap 

plate) 

 

Summary of Contents for ALGO 5





















Reviews: