background image

First Printing — May 1997

Copyright 1997

Copyright 1997

NEC Computer Systems Division 

NEC Corporation

Packard Bell NEC, Inc.

7-1 Shiba 5-Chome, Minato-Ku

1414 Massachusetts Avenue

Tokyo 108-01, Japan

Boxborough, MA  01719-2298

All Rights Reserved

All Rights Reserved

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related
materials, is the valuable property of NEC Computer Systems Division, Packard Bell NEC,
Inc. (hereinafter “NECCSD”) and/or its licensors. NECCSD and/or its licensors, as appro-
priate, reserve all patent, copyright and other proprietary rights to this document, including
all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent
said rights are expressly granted to others.

The NECCSD product(s) discussed in this document are warranted in accordance with the
terms of the Warranty Statement accompanying each product. However, actual
performance of each such product is dependent upon factors such as system configuration,
customer data, and operator control. Since implementation by customers of each product
may vary, the suitability of specific product configurations and applications must be
determined by the customer and is not warranted by NECCSD.

To allow for design and specification improvements, the information in this  document is
subject to change at any time, without notice. Reproduction of this document or portions
thereof without prior written approval of NECCSD is prohibited.

NEC is a registered trademark of NEC Corporation, and FastFacts, MagicEye, MultiSync, and PowerMate

are either trademarks or registered trademarks of NEC Technologies, Inc.; these trademarks are used
under license by Packard Bell, NEC.

All other  product, brand, or trade names used in this publication are the trademarks or registered

trademarks of their respective trademark owners.

Summary of Contents for MT-2550-24874C























































































































































































































Reviews: