background image

ProSafe Wireless-N VPN Firewall 
SRXN3205 Reference Manual 

 

 

© 2008 by NETGEAR, Inc. All rights reserved.   

Trademarks 

 

NETGEAR and the NETGEAR logo are registered trademarks and ProSafe is a trademark of NETGEAR, Inc. 
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product 
names are registered trademarks or trademarks of their respective holders. 

 

Statement of Conditions 

 

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to 
make changes to the products described in this document without notice.   

NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit 
layout(s) described herein. 

 

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency 
Notice 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:   

.

 

• Reorient or relocate the receiving antenna.   

.

 

• Increase the separation between the equipment and receiver.   

.

 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.   

.

 

• Consult the dealer or an experienced radio/TV technician for help.   

 

1.0, July 2008 

 
 

Summary of Contents for SRXN3205 - ProSafe Wireless-N VPN Firewall Wireless Router























































































































































Reviews: