In the event that you should require service for your Nikon
RIFLESCOPE, in case of USA market, please send it directly to:
Nikon Scope Service
841 Apollo Street, Suite 100
EI Segundo, CA. 90245-4721
1-800-Nikon SV.
In other market, please bring it to dealer from which you purchased it.
Pour les autres marchés, veuillez apporter la lunette de visée au
magasin où vous l'avez achetée.
3-9x40
Instruction manual / Mode d'emploi
MUZZLELOADING RIFLESCOPE
F
E
3-25, Futaba 1-chome, Shinagawa-ku, Tokyo 142-0043, Japan
Tel:+81-3-3788-7697 Fax:+81-3-3788-7698
Manufacturer:
Printed in the Philippines (545B)1E/1107
Imprimé aux Philippines
Congratulations on your choice of a Nikon INLINE XR Muzzleloading Riflescope. Your new scope is
the finest example of Nikon's rugged and durable construction and precision bright optics; important
qualities for a serious shooter's riflescope.
Whether you use your scope for hunting or for target shooting, the procedure for mounting is
identical. You should acquire a set of high quality steel mounting rings which have a standard
diameter of 25.4 mm (1 inch). Follow the ring manufacturer's instructions for mounting procedures.
After mounting the scope on your muzzleloader, follow the procedures for reticle alignment.
When setting the reticle for hunting, you should determine your standard range and then adjust the
reticle based upon that target distance. For targets which vary from that standard distance you may
simply adjust the position of the reticle in relation to your target, or you may wish to use the
procedure for trajectory compensation. It's up to your personal preference.
We hope that you will enjoy your new Nikon INLINE XR Muzzleloading Riflescope for many years to
come. Enjoy using it, and above all, always follow safe shooting procedures!
The product(s) described herein may be subject to export control regulations in the relevant
country(ies). It (they) should not be exported without authorization of the exporting governmental
authority if the regulations apply.
Caution
(1) Do not look at the sun through the riflescope. It will permanently damage your eye. This
precaution applies to all optical devices such as cameras and binoculars.
(2) The riflescope is effectively sealed against moisture and dust. You may use your scope
safely either in the rain or in dusty climates. To preserve the appearance of the scope, we
suggest that it be dried and cleaned prior to storage. Use a soft cloth for cleaning metal
surfaces and use photographic lens tissue to clean the scope's lenses.
1. Nomenclature
Magnified Figure of
Hand turn Grip
Fig. 1-2
Fig. 1-1
2. Specifications
Model
Actual Magnification
3-9x40
3-9x
40
1.57
4.4
0.17
127.0-127.0
5.0-5.0
8.4-2.8
25.2-8.4
25.4
1
49.3
1.94
288
11.3
390
13.8
1 click = 1/4"
60
91.44
100
42
1.65
Objective Diameter
(mm)
(in)
Exit Pupil
(mm)
(in)
Eye Relief
(mm)
(in)
Field of View at 100m/yd
(m)
(ft)
Tube Diameter
(mm)
(in)
Objective Tube Diameter
(mm)
(in)
Length
(mm)
(in)
Weight
(g)
(oz)
Adjustment Graduation
(moa)
Maximum Internal
Adjustment
(Elevation & Windage)
(moa)
Parallax Setting
(at factory)
(m)
(yards)
Structure
★
Waterproof (maximum depth of 2 meter
for up to 5 minutes) and Nitrogen Gas
Outside Diameter of
Eyepiece
(mm)
(in)
3. Instructions
(1) Focusing
●
Look through the eyepiece with your eye positioned about 10 cm (4 in) away from the
eyepiece lens (Fig. 3-1), and you will see the BDC 300 reticle (Fig. 3-2).
Be sure your eye is positioned within proper alignment and proper eye relief otherwise the
view will "black out".
●
Point the objective end of the scope at the sky (Do not point at the sun) or at a plain
unpatterned wall.
Turn the eyepiece adjustment counter-clockwise and then turn it clockwise until the reticle
appears sharp.
(2) Magnification
The INLINE XR Riflescope has a variable magnification from 3 to 9x.
To change powers, just rotate the power selector ring until the desired magnification appears
adjacent to the power index dot (Fig. 1-1).
(3) Adjustment of the riflescope
Sighting through the riflescope, align the rifle with your aiming point on the target and shoot a
trial round. If the bullet does not hit the aiming point, adjust the elevation and windage after
removing the Adjustment cap, as follows:
For the INLINE XR Riflescope adjustment is made by turning the grip by hand. If the bullet hits
under the aiming point, turn the grip in the direction of the arrow marked "U" (Fig. 3-3). If the
bullet hits to the left of the aiming point, turn the grip in the direction of the arrow marked "R"
(Fig. 3-3).
(4) Zero setting of grip
(Fig. 3-4)
After the reticle has been adjusted to the point of impacts, with the grip held with your fingers to
avoid shifting of the aligned grip, turn the grip screw in top of the grip counterclockwise with
coin. Then lift the grip up and align the "
▼
" with the index mark. It may happen that the "
▼
"
could not align with the index mark exactly because of the coupling pitch of the grip with the
shaft. And by securing the grip with your fingers to avoid shifting of the grip, turn the grip screw
clockwise with the coin until the grip is firmly secured.
Note:
●
The windage and elevation scales of the INLINE XR Riflescope are calibrated in divisions of
1/4 minute of angle with a click at intervals of 1/4 minute of angle.
●
When adjusting the reticle to the point of aim, remember that one minute of angle equals
approximately one inch (2.54 cm) at 100 yards (91.44 m). Therefore, if the impact point is
two inches (5.08 cm) low and one inch (2.54 cm) right at 100 yards (91.44 m), you should
adjust two minutes of angle up one minute of angle left.
Maintenance
(1) Lens cleaning
To remove dirt or fingerprint, soak gauze or lens cleaning paper (silicon-free paper sold at
camera shop) with a small quantity of absolute alcohol (available from drugstore) and lightly
wipe off. Wiping with handkerchief of leather is not recommended as it is likely to damage the
lens surface.
Dust may scratch the lens surface or corrode the lens.
Brush dust off using a soft oil-free brush.
(2) Scope Exterior
Use a soft dry cloth to wipe off any dirt or finger-prints that might accumulate.
It is not necessary to oil the scope's surface.
(3) Windage/Elevation Adjustments
These adjustments are permanently lubricated. Do not attempt to lubricate them. Cover with
caps supplied, except when adjusting, to keep out dust and dirt.
(4) Eyepiece Adjustment
This adjustment is permanently lubricated. Do not attempt to lubricate.
(5) Power Selector Ring
No lubrication is required on the power selector ring.
Do not loosen or remove screws in power selector ring.
Waterproof models:
The Nikon Riflescope is waterproof, and will suffer no damage to the optical system if submerged or
dropped in water to a maximum depth of 2 meters for up to 5 minutes.
The Nikon Riflescope offers the following advantages:
●
Can be used in conditions of high humidity, dust and rain without risk of damage.
●
Nitrogen-filled design makes it resistant to condensation and mold.
Observe the following when using the Nikon Riflescope.
●
As the unit does not have a perfectly sealed structure, it should not be operated nor held in
running water.
●
Any moisture should be wiped off before adjusting movable parts (Elevation / Windage
adjustment knob, eyepiece, etc.) of the Nikon Riflescope to prevent damage and for safety
reasons.
To keep your Nikon Riflescope in excellent condition, Nikon Vision recommends regular
servicing by an authorized dealer.
＊
Specifications and design are subject to change without notice.
＊
No reproduction in any form of this "Instruction manual," in whole or in part (except for brief quotation in critical
articles or reviews), may be made without written authorization from NIKON VISION CO., LTD.
3-9x40
Fig. 3-3
Eyepiece Adjustment
Eye Relief
Fig. 3-1
Objective Lens
Eyepiece Lens
Elevation Adjustment
Windage Adjustment
Eyepiece Adjustment
Power Index Dot
Power Scale
Power Selector Ring
Adjustment Cap
＊
(545B)1E/1107
(at minimum magnification)-(at maximum magnification)
moa=minute of angle (in front of 100 yards one moa is nearly equal to one inch.)
Nikon riflescopes are factory set to be parallax free at 100 yards (91.44 m).
＊
＊＊
＊＊＊
＊＊＊
＊
＊＊
Fig. 3-4
Fig. 3-2
BDC 300 Reticle
