background image

w w w . h a w k e y e e l e c t r o n i c s . c o m  

 

 

 

To ensure safety and many years of trouble-free 
operation of your product, please read this 
manual carefully before using this product. 

SAFETY INFORMATION: 

 

 

Periodically wipe the face with a dry cloth. Do not use abrasives or 
solvents on this device. 

 

Only qualified personnel should perform repairs or servicing not covered 
in this manual. 

 

The LCD used in the product is made of glass.  Therefore, it can break 
when the product is dropped or impacted. 

 

Keep this product away from heat sources such as radiators, heaters, 
stoves and other heat generating sources.  Do not store in extreme 
temperatures above 150° F (65° C).   

 

Shade the LCD during storage.  Do not expose LCD to direct sunlight for 
extended periods of time.   
 

NOTES, NOTICES, AND CAUTIONS 

 

WARNING:

  Indicates a potential for property damage, personal injury or 

death. 

 

IMPORTANT:

  Indicates potential damage to the device and tells you how to 

avoid it. 

 

NOTICE:

  Indicates important information that helps you make better use of 

the device and tells you how to correct a performance problem. 

 

I

NFORMATION

:  Indicates resources to obtain the proper information to help 

you make the most of your device. 

 

I

NFORMATION

Read this manual completely before attempting to use or 
install your device.  Visit our Customer Service Center on our 
website for advanced troubleshooting and technical support. 

 

W

ARNING

This depth sounder should not be used as a navigational aid 
to prevent grounding, boat damage, or personal injury. Always 
operate the boat at slow speeds in unfamiliar water, or if you 
suspect shallow water or submerged objects. 

 

Model No.   

D10D

 

INSTALLATION AND OPERATION MANUAL 

D11S – Surface Mount Digital Depth Sounder with Transom/Glue-In Transducer 

Summary of Contents for HawkEye D11S





























Reviews: