background image

Downflow, Direct Vent (Sealed Combustion)
Forced Air Gas and Oil Furnaces

Installation Instructions/Owners Manual

Series M1B, M1G, M1M and M1S

For installation in:

1. Manufactured Homes
2. Recreational Vehicles, Park Models, Manufactured Buildings
3. Modular Homes/Buildings

LEAVE THESE INSTRUCTIONS WITH THE HOMEOWNER.

–Do not store or use gasoline or other flammable va-

pors and liquids in the vicinity of this or any other
appliance.

–WHAT TO DO IF YOU SMELL GAS

• Do not  try to light any appliance.
• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

–Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

WARNING:

If the information in this manual is not followed exactly,
a fire or explosion may result causing property damage,
personal injury or loss of life.

!

Should overheating occur, or the gas supply fail to shut off, shut off the manual gas valve to the
appliance before shutting off the electrical supply.

WARNING:

!

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Refer to this manual. For assistance or additional information consult a
qualified installer, service agency or the gas supplier.

!

WARNING:

Do not use this appliance if any part has been submerged under water. Immediately call a
qualified service technician to inspect the appliance and to replace any part of the control
system and any gas control that has been submerged underwater.

!

Summary of Contents for M1GB 056





























Reviews: