background image

AIR HANDLER

Please read all information in this manual thoroughly and become familiar with the capabilities 
and use of your appliance before attempting to operate or maintain this unit. These instructions 
are primarily intended to assist qualified individuals experienced in the proper installation 
of this appliance. Installer should be specifically trained to install and setup an iQ system. 
Some local codes require licensed installation / service personnel for this type of equipment. 
Improper installation, service, adjustment, or maintenance may cause explosion, fire, electrical 
shock or other hazardous conditions which may result in personal injury or property damage.

Unless otherwise noted in these instructions, only factory authorized kits or accessories may 
be used with this product. Keep this manual where you have easy access to it in the future. If a 
problem occurs, check the instructions and follow recommendations given. If these suggestions 
don’t eliminate your problem, call your servicing contractor.

DO NOT DESTROY. PLEASE READ CAREFULLY AND 

KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

IMPORTANT

B6VMAI

INSTALLATION INSTRUCTIONS

 

Series

Summary of Contents for B6VMAI





















Reviews: