background image

 

1 rev. 

 050312

Model  NSJ0302

3 Ton Capacity Aluminum Service Jack

For Technical Questions, Call: 1-800-879-7316

WARNING INFORMATION

This is the safety alert symbol. It is used to alert you 

to potential personal injury hazards. Obey all safety 

messages that follow this symbol to avoid possible 

injury or death.

             

 

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS JACK, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING

PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using this jack. It is also the responsibility of the jack owner 

to keep this manual intact and in a convenient location for all to see and read. Contact PowerStation, LLC for a replacement label if your jack's label 

is not readable. If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the 

operator's native language by the purchaser/owner or his designee, making sure that the operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting and support devices is subject to certain hazards that cannot be prevented by mechanical means, but only 

by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and operation 

of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its proper use. Examples of hazards 

are dropping, tipping or slipping of loads caused primarily by improperly secured loads, overloading, off-centered loads, use on other than hard level 

surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

•  Read, study, understand and follow all instructions before operating this device.

•  Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or unstable due to 

loose or missing components. Make corrections before using.

•  Lift only on areas of the vehicle as specified by the vehicle manufacturer.

•  Wear eye protection that meets ANSI Z87.1 and OSHA standards.

•  Do not use jack beyond its rated capacity.

•  This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before working on the 

vehicle.

•  Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering operations.

•  Center load on saddle. Be sure setup is stable before working on vehicle.

•  Do not move or dolly the vehicle while on the jack.

•  Do not use saddle adapters or saddle extenders between the stock lifting saddle and the load.

•  Do not use any adapters unless approved or supplied by PowerStation, LLC.

•  Always lower the jack slowly and carefully.

•  This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

 

Wash hands thoroughly after handling.

•  Failure to heed these warnings may result in fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, 

MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS could 

cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 

which, if not avoided, could result in death 

or serious injury.

WARNING

WARNING

WARNING

WARNING

Summary of Contents for NSJ0302

Page 1: ... for a purpose for which it was not designed METHODS TO AVOID HAZARDOUS SITUATIONS Read study understand and follow all instructions before operating this device Inspect the jack before each use Do not use jack if damaged altered modified in poor condition leaking hydraulic fluid or unstable due to loose or missing components Make corrections before using Lift only on areas of the vehicle as speci...

Page 2: ...in the receiver in the bottom of the handle Secure the handle in the handle socket by tightening the handle bolt 3 Sometimes air gets trapped in the hydraulic system during shipping and handling If the pump feels spongy or there is not a full incremental pump stroke or the jack will not raise to maximum height follow these instructions in order to purge air from the system a With the lift arm in i...

Page 3: ... grit before using 2 The jack must be lubricated periodically in order to prevent premature wearing of parts A general purpose grease must be applied to caster wheels front axle elevator arm handle base pivot bolts release mechanism and all other bearing surfaces Worn parts resulting from inadequate or no lubrication are not eligible for warranty consideration IMPORTANT In order to prevent seal da...

Page 4: ...or replace at our option any part or unit which proves to be defective in material or workmanship Other important warranty information This warranty does not cover damage to equipment or tools arising from alteration abuse misuse damage and does not cover any repairs or replacement made by anyone other than PowerStation LLC The foregoing obligation is PowerStation LLCs sole liability under this or...

Reviews: