background image

BP27 ULTRA MAXX

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS

BEFORE OPERATING OR SERVICING MACHINE

DANGER !

Failure to Observe These Instructions Can Cause Personal Injury
to Machine Operator, By-Standers or Possible Machine Damage.

• 

ALWAYS

 wear eye protection and protective clothing when working with the batteries.

• 

The batteries contain 

ACID

. Avoid contact with skin or clothing.

• 

Antidote: 

EYES

 - Flush with water 15 minutes. Call physician.

    

INTERNAL

 - Drink water or milk. Follow with Milk of Magnesia, beaten egg or vegetable oil. Call

                  physician.

• 

Service should be done only by authorized, trained personnel.

• 

Charge Batteries in a well ventilated area with Battery Compartment Open.

• 

Batteries generate explosive gasses - keep sparks, flames, burning cigarettes or other ignition sources away

   at all times.

• 

Batteries are heavy - two (2) people are required for installation or removal.

• 

Never lay anything on top of batteries to prevent arcing.

• 

Turn off all switches during installation and service.

• 

To maintain machine balance, always slide batteries back into position as shown on battery installation decal.

• 

Connect batteries as shown on battery installation decal to avoid shorting out batteries and electrical system.

• 

Disconnect battery leads before performing any service or repairs.

• 

ALWAYS

 make sure battery charger is turned off when connecting/disconnecting to machine to prevent

  sparking.

• 

ALWAYS

 operate this machine from the rear control panel, not from the side.

• 

NEVER

 operate machine in an explosive atmosphere (grain dust or gas vapor).

• 

NEVER

 use flammable liquids (gas, kerosene, solvents or thinners) to clean floor.

• 

ALWAYS

 turn off master switch when changing pads.

• 

NEVER

 operate machine with skirts or covers removed.

• 

NEVER

 leave machine unattended.

  PERSONAL INJURY AND PROPERTY DAMAGE FROM MACHINE OVERTURNING, BATTERIES FALLING
  OUT OF MACHINE OR BATTERIES LEAKING ACID CAN OCCUR IF YOU DO NOT FOLLOW THESE
  PRECAUTIONS:

• 

NEVER

 attempt to operate machine unless you have been trained in its operation.

• 

Follow these rules when working on or near loading docks and ramps:

• 

ALWAYS

 be sure ramp is secured to vehicle before attempting to load/unload.

• 

ALWAYS

 use extreme caution when operating machine on a ramp or loading/unloading a machine into or out

  of a truck. Use extreme caution if ramp is wet, oily or covered with cleaning chemicals.

• 

NEVER

 turn machine on an incline.

• 

NEVER

 stop machine on a ramp.

• 

NEVER

 attempt to climb a grade of more than 20 degrees.

• 

NEVER

 park machine near a dock or on ramps.

• 

NEVER

 leave machine unattended.

WARNING: Failure to observe these instructions can cause machine damage and possible personal
 injury to machine operator.

• 

NEVER

 spray machine with water.

• 

NEVER

 allow battery charging plugs to get wet. Battery charging plugs will short out if wet.

• 

NEVER

 operate machine when charger is plugged in.

• 

NEVER

 store machine near furnaces, boilers or flame which may damage machine.

• 

NEVER

 store any item on the machine.

• 

ALWAYS

 protect machine from freezing temperatures.

SAVE THESE INSTRUCTIONS

https://harrissupplyind.com - To Order Parts Call 608-268-8080

Summary of Contents for BP27 ULTRA MAXX





















Reviews: