background image

Mounting in the

 vertical

 orientation shown above IS NOT ADVISABLE 

for LPHW units due to the actuator being below the valve. 

Service/Maintenance Access – Unit must be installed with a 

minimum of unit depth as additional clearance i.e DS1A-NES 

either allow 233mm above or below unit.

For systems which include supply fans with heating other than 

where the BMS (0-10V) has control, the appropriate user control is

 

required (i.e. ES-LCD or ES-CI

)

.

The EMC Directive 
20

1

4/

30

/E

U

  

The Low Voltage 
Directive 
20

14/3

5/E

U

18. 10. 17. Leaflet Number 671679

DAVE Supply Fans (ES Models) 50/60Hz

For Internal and External use

Installation & Maintenance Instructions

Assembly with
base frame.

Palletised.

Forklift.

Slings via spreaders fitted to unit
with base frame.

Please note that above images are
examples of typical lifting methods. 
Actual unit lifting plan and risks
must be assessed by competent 
personnel before moving the unit.

DS1A-NES

H

| |

 

|

 

|

|

|

1 2

 

3

 

4 5

6

1. 

DAVE Range 

2. 

Supply fan

3. 

Case size (1-7)

4. 

L = LPHW Coil/valve
E = Electric heater

   

= No heater

5. 

ES

 

= Ecosmart control

6. No suffix = 50Hz

H = 60Hz 

Front Elevation

Control

Airflow

DAVE Supply Fans

The Dave range of in-line backward curve fans consisting of 
9 duty sizes with a maximum of 1.1m

3

/s (1100l/s).

Units are manufactured from aluzinc, rectangular in section and have
circular rigid spigots at each end. All units are supplied with fixing
brackets designed to simplify installation.

1.0 Fan Unit Coding Descriptions

2.0 Handling

Always handle the units carefully to avoid damage and distortion.
Care must be taken to ensure any slings used for hoisting do not
damage the casing or the control module components. 

Note: The weight of the unit is on the rating plate.

Figure 1: Typical lifting methods.

3.0 Installation

Installation must be carried out by competent personnel, in 
accordance with good industry practice, the appropriate authority

 

and in conformance with all statutory and governing regulations. 

Access to the unit for maintenance is via the top or bottom lid,

 

therefore this should be taken into account before installation 
takes place (See important note below).

Figure 2: Mounting in t

he vertical

 orientation

 below

 is not advisable 

(LPHW units only).

Units are supplied complete with four support mounting brackets 
for quick and easy installation, either surface mounted or suspended
with drop rods. 

Figure 3: Units supplied with four mounting brackets with 
1 x M8 hole in each.

External units must not be installed at an angle over 5° from 

the horizontal.

Nuaire: A Trading Division of Polypipe Limited

  

Western Industrial Estate Caerphilly  United Kingdom  CF83 1NA  

T: 029 2088 5911  F: 029 2088 7033  E: info@nuaire.co.uk  W: www.nuaire.co.uk

1

Summary of Contents for DAVE Series










Reviews: