background image

NS54000 SERIES

Page 1

CHIMNEY 
RANGE HOOD

READ AND SAVE THESE INSTRUCTIONS

WARNING  

 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 

TO PERSON(S) OBSERVE THE FOLLOWING:
1.  Use this unit only in the manner intended by the manufacturer. 

 If you have questions, contact the manufacturer at the 

 address or telephone number listed in the warranty.

2.  Before servicing or cleaning unit, switch power off at service 

 panel and lock service disconnecting means to prevent 

 power from being switch on accidentally. When the service 

 disconnecting means cannot be locked, securely fasten a 

 prominent warning device, such as a tag, to the service panel.

3.  Installation work and electrical wiring must be done by qualified 

personnel in accordance with all applicable codes and standards, 

including fire-rated construction codes and standards.

4.  Sufficient air is needed for proper combustion and exhausting 

 of gases through the flue (chimney) of fuel burning equipment 

 to prevent backdrafting. Follow the heating equipment 

 manufacturer’s guidelines and safety standards such as 

 those published by the National Fire Protection Association 

 (NFPA), the American Society for Heating, Refrigeration 

 and Air Conditioning Engineers (ASHRAE) and the local 

 code authorities.

5.  This product may have sharp edges. Be careful to avoid cuts and 

abrasions during installation and cleaning.

6.  When cutting or drilling into wall or ceiling, do not damage 

 electrical wiring and other hidden utilities.

7.  Ducted fans must always be vented to the outdoors.
8.  Use only metal ductwork.
9.  Do not use this unit with any other solid-state speed control 

device.

10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1.  Never leave surface units unattended at high settings. 

 Boilovers cause smoking and greasy spillovers that may 

 ignite. Heat oils slowly on low or medium settings.

2.  Always turn hood ON when cooking at high heat or when

 cooking flaming foods (i.e. Crêpes Suzette, Cherries Jubilee,

 Peppercorn Beef Flambé).

3.  Clean ventilating fans frequently. Grease should not be 

 allowed to accumulate on fan or filters.

4.  Use proper pan size. Always use cookware appropriate for 

 the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSON(S) IN THE EVENT 

OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1.  SMOTHER FLAMES with a close-fitting lid, cookie sheet, or 

 

metal tray, then turn off the burner. BE CAREFUL TO PREVENT 

 

BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, 

 

EVACUATE AND CALL THE FIRE DEPARTMENT.

CAUTION  

!

1.  For indoor use only.
2.  For general ventilating use only. Do not use to exhaust 

 

hazardous or explosive materials and vapors.

3.  To avoid motor bearing damage and noisy and/or 

 

unbalanced impeller, keep drywall spray, construction dust, 

etc. off power unit.

4.  Do not use over cooking equipment greater than 60,000 BTU/hr. 

as the blower motor will shut down intermittently.

5.  Your hood motor has a thermal overload which will 

 

automatically shut off the motor if it becomes overheated. 

The motor will restart when it cools down. If the motor 

continues to shut off and restart, have the hood serviced.

6.  The bottom of the hood MUST NOT BE LESS than 24” and at 

a maximum of 30” above cooktop for best capture of cooking 

impurities.

7.  Two installers are recommended because of the size of 

this hood.

8.  To reduce risk of fire and to properly exhaust air, be sure 

to duct air outside. Do not exhaust air into spaces within 

walls or ceilings or into attics, crawl spaces, or garages.

9.  Be careful when installing the decorative flue and hood, they 

may have sharp edges.

10. Please read specification label on product for further 

 

information and requirements.

INSTALLER: Leave this guide with the 

homeowner.

HOMEOWNER: Operation and maintenance 

information on page 2.

Register your product online at 

www.nutone.com/register

WARNING  

 

2.  NEVER PICK UP A FLAMING PAN – You may be burned.
3.  DO NOT USE WATER, including wet dishcloths or towels –  

 

This could cause a violent steam explosion.

4.  Use an extinguisher ONLY if:
  

A.  You know you have a Class ABC extinguisher and you  

     know how to operate it.
  

B.  The fire is small and contained in the area where it 

 

       started.
  

C.  The fire department has been called.

  

D.  You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

!

 

FOR DOMESTIC COOKING ONLY 

!

Summary of Contents for NS54000 Series





























Reviews: