background image

TOYOTA

  

 

Reference

  450Q 

Preparation 

   

Issue B 5/23/16 

 

                    Page | 1 

   
   

   

Table of Contents

 

I. Preparation

................................................................................................................1-2  

1. Table Of Contents ..................................................................................................2 

II. Procedure

 ...............................................................................................................3-23  

1.  Vehicle Preparation ..............................................................................................3 
2.  Radio Removal ................................................................. ................................3-4 
3.  Quick-Sync Wiring Harness Installation.............................................................4-7 
4.  Subwoofer Umbilical Installation.........................................................................7-9 
5.  Rear Speaker Bypass Cable Installation.........................................................10-12 
6.  Power wire Installation.....................................................................................12-14 
7.  Installation of the Fuse Holder..............................................................................15 
8.  Amplifier Installation..........................................................................................15-17 
9.  Dash Speaker installation ................................................................................17-18 
10. Front Door Speaker Installation ........................................................................19-21 
11. Subwoofer Installation.......................................................................................21-23 
12. Fuse Installation....................................................................................................23 

13. Set Clock to correct time.......................................................................................23 

14. Verify Radio Settings............................................................................................ 

15. Checklist / Troubleshooting................................................................................... 

Accessory Installation Practice (read before installation) 

 

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The 
installation of this accessory should follow approved guidelines to ensure a quality installation.  

These guidelines can be found in the “Accessory Installation Practices” document.  

This document covers such items as:  

• 

Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)  

• 

Safety (eye protection, checking torque procedure, etc.)  

• 

Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)  

• 

Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)  

   Please see your Toyota/Scion/Lexus dealer for a copy of this document. 

 

Revisions and other installation assets  

OEM Audio Plus is committed to providing components and instructions designed for seamless integration. 
Please visit oemaudioplus.com for the most up to date installation related documents and media,   

Important Warranty Information Failure to completely and properly fill out online Warranty 
Registration may result in possible reduction or complete denial of future warranty claims

. Complete 

yours today at: 

oemaudioplus.com/registration

 or call: 

855 OEM-ODIO

 for more details and alternative 

methods of system registration. 

Summary of Contents for Reference 450Q






















Reviews: