• Handle the power cord with care.
Do not modify or attempt to repair the cord.
Do not place any object on top of the cord.
Avoid excessive vending, twisting, and pulling.
Do not place cord near heating equipment.
Check that the plug is clean before plugging it in.
Be sure to push the prongs all the way in.
*Improper handling may lead to fire or electric shock.
If the cord becomes damaged, contact your dealer for advice.
• Please keep the poly bag which this equipment is packed in away from children or throw it away
to prevent children from putting it on.
*Putting on it may cause suffocation to them.
•
Unpacking and preparation
Confirm that the package includes the power unit, power cord and this sheet. If the power unit is
damaged or incomplete, contact your dealer for assistance.
After unpacking, save the packaging materials so that you can reuse them for future transport of the
unit.
•
Usage and Storage Locations
The power unit should always be kept in a safe and stable environment, both when in use and when
in storage. In particular, keep the unit away from the following:
Usage Precautions for the PS60A-24B Power Unit
• Direct sunlight
• Extreme changes in temperature or humidity
• High levels of dust
• Fire
• High temperature and humidity
• Heating and cooling equipment
• Volatile materials
• Locations where it might became wet
• Vibration and impact
•
Connecting the power Unit to the Power Cord
Be sure to push the end of the power cord all the way into the AC inlet. The fitting on the cord should
make contact with the back of the inlet.
SAfety PreCAUtionS
This document presents important information intended to ensure safe and effective use of this
product. Please read this document carefully, and
store it in an accessible location near your
installation
.
SAfety PreCAUtionS ----- Be SUre to oBSerVe
In order to prevent hazards to an operator or other persons and damage to property, be sure to
observe the following precautions.
The following describes the degrees of hazard and damages that can occur if the given instructions
are neglected or the equipment is incorrectly operated.
•
Additional Safety Precautions
• Never attempt to stretch the cords to enable a connection. The power cord and DC cable must have
adequate slack at all times during use.
• Never allow the power unit to hang from the power cord or DC cable.
• Do not place metallic parts (such as fasteners)in contact with the DC cable.
• Do not connect the unit to a table tap or extension cord.
• Do not use aerosol cleaners, alcohol, thinner, benzine etc. to clean the power unit.
The power cord supplied is dedicated to the PS60A-24B power unit.
Federal Communications Commission Radio Frequency Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This statement will be applied only for the printers marketed in U.S.A.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
For compliance with the Federal Noise Interference Standard, this equipment requires a shielded
cable.
For RF interference suppression, if a ferrite core is provided with this device, affix it to the interface
cable.
Statement of The Canadian Department of Communications Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The above statement applies only to printers marketed in Canada.
Negligence of this precaution may result in death or serious
injury.
Negligence of this precaution may result in injury or dam-
age to property.
WArninG
CAUtion
WArninG
• Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise.
* Immediately unplug the equipment and contact your dealer for advice.
• Never attempt to repair this product yourself. Improper repair work can be dangerous.
• Never disassemble or modify this product.
* Tampering with this product may result in injury, fire, or electric shock.
• Be sure to use the specified power source.
* Connection to an improper power source may cause fire or electric shock.
• Never insert or disconnect the power plug with wet hands.
* Doing so may result in severe shock.
• Do not allow foreign object to fall into the equipment.
* Penetration of foreign object may lead to fire or electric shock.
• If water or other liquid spills into this equipment unplug the power cord immediately, and then
contact your dealer or a service center for advice.
* Continued usage may lead to fire or electric shock.
• Do not place multiple loads on the power outlet (wall outlet).
* Overloading the outlet may lead to fire.
• Always supply power directly from a standard domestic power outlet.
WArninG
WArninG
• Be sure your power cord meets the relevant safely standards.
• Do not connect this product to any equipment other than the ”Supported Devices”. Do not con-
nect it to equipment from other manufacturers. Use this product only for its intended application.
*Improper usage may lead to equipment damage, fire, or electric shock.
• Be sure to set this equipment on a firm, stable, horizontal surface.
*Product may break or cause injury if it falls.
• Do not use in locations subject to high humidity or dust levels.
*Excessive humidity and dust may cause equipment damage, fire, or electric shock.
• Do not place heavy objects on top of this product. Never stand or lean on this product.
*Equipment may fall or collapse, causing breakage and possible injury.
• To ensure safety, please unplug this product prior to leaving it unused for an extended period.
•
important Safety rules
• Do not connect to electric outlets close to devices that generate voltage fluctuations or electric
noise. In particular, stay clear of devices that use large electric motors.
• Always connect the DC cable before plugging the power cord into the wall outlet.
• When disconnecting power, always unplug the power cord from the wall outlet before disconnecting
the DC cable.
• When disconnecting the DC cable, hold it firmly at the connector area. Do not tug on the cord itself.
• To clean the unit, wipe with a dry or slightly moistened (and firmly wrung) cloth.
Never clean the unit while it is plugged into the wall outlet.
• Note that this unit is not equipped with an ON/OFF switch.
Keep in mind that you may need to pull the plug out of the socket in order to cut the power in the
event of a problem with the connected device.
im00160EN PS60A-24B
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.”
DC cable
Power unit
Power cord
Plug
AC inlet
DC cable connector
