Ÿ
BATTERY CHARGE
Firstly, slide the USB port cover aside, then connect the flashlight to external
USB power supply, the status indicator turn on means charging is in process.
Thank you for purchasing Olight products! Please read this manual
carefully before use.
Within
30
days of purchase
:
Return
to
retailer
from which you purchased
for repair or replacement.
Within
5
years
of
purchase
:
Return
to
Olight
for
repair or replacement.
This warranty does not cover normal wear and year,modifications, misuse,
disintegrations,negligence, accidents, improper maintenance, or repair by
anyone other than an Authorized retailer or Olight itself.
NOTE:
One of the following output modes low, medium, high, will be
memorized when the light shutting off. The flashlight will not
memorize the low mode when the light is activated to low mode
directly before it is turned off. For high mode, the light will only
memorize high mode for 10 minutes when the light is off, after 10
minutes the memorized mode will switch to medium mode.
Technical support:
techsupport@olightworld.com
Customer service:
cs@olightworld.com
Website:
www.olightworld.com
WARRANTY
SPECIFICATIONS
1,600 lumens / 3 hours
600 lumens / 8
hours
120 lumens / 36 hours
10Hz
3xCree XM-L2
CW
2.8 to 6v
18,000cd
268 meters
3 x 18650 (with protecting circuit board)
Type
Ⅲ
hard
anodized
aluminum
IPX
8
L
132
mm x D
47.5
mm
/
5
.
2
in
x
1.9in
Ÿ
TURN ON/OFF
Quick click the side switch to turn the flashlight on or off. The light will turn to
the last output mode before shutting off.
Ÿ
CHANGE BRIGHTNESS LEVELS
With the light on, press and hold the side switch, the output will cycle through
low, medium, and high brightness levels. Release the side switch when the
desired brightness level is achieved.
Ÿ
LOW MODE
With light off, press and hold the side switch for more than 1 second, the low
mode will be activated.
Ÿ
TURBO MODE
Double-click the side switch to activate turbo mode if the light is in non-
locking state.
Ÿ
STROBE MODE
When the light is in non-lock state, Triple-click side switch to activate strobe
mode. Click the side switch once to quit strobe mode, press and hold side
switch to turn on the setting of changing brightness level.
Ÿ
LOCK MODE
With the light off, press the side switch and hold for 1 second to activate low
mode, keep holding the switch for one more second, the light will shut off
automatically and lock the side switch. Under lock state, click and release the
switch, the red indicator will last for 2 seconds.
Ÿ
UNLOCK MODE
When the light is off, press and hold side switch for more than 2 seconds, the
switch is enable and activate low mode. User may twist the tail cap anti-
clockwise to turn off the light, tighten the tail cap clockwise to unlock the
light.
Ÿ
STATUS
INDICATOR
There is a multi-purpose status indicator lamp at the upside of the USB
charging port to indicate the battery low voltage or charging state:
Battery low voltage indication: When the battery voltage is less than 3.25V,
the status indicator lamp will flicker in red; when the battery voltage is less
than 3.05V, the status indicator lamp will be a constant red.
Charging state indication: red means under charging; green means fully
charged.
3,200 lumens
All performance claim to ANSI/NEMA FL1-2009 standard
Made
in
China
TURBO
HIGH
MED
LOW
STROBE
LED
Operate Voltage
Candela
Beam Distance
Supported Batteries
Material
Water-proof
Impact
Resistance
Dimensions
Weight
181g / 6.4oz (excluding batteries)
1.5 meters
SUPPORTED
BATTERIES
INSIDE
THE
BOX
Flashlight, holster, USB cable, user manual (this manual), and other optional
accessories( refer to the label marks outside of box for detail)
3 x 18650 rechargeable lithium batteries with protecting circuit board , the
batteries must have a protruding button on positive pole.
Note: Tests performed with 3x18650 batteries (3400mAh,3.6v)
OPERATION
INSTRUCTION
Ÿ
BATTERY
INSTALLATION
Before use, install the batteries and notice that the battery positive towards
the flashlight head, then tightly screw the tail-cap as shown below.
WARNING
:
CONTACT
Do not mix rechargeable and non-rechargeable batteries.
Do not mix batteries of different types/brands.
Properly install the batteries, the positive of battery towards the head of
the flashlight, three batteries are in same direction.
The product only support the batteries with protruding button on the
positive and with protecting circuit board, recommend to use the battery
cell capacity of 18650 with 3000mAh or above.
Low battery protection: if the battery v oltage drop down to 2.7V, the
flashlight will not turn on, the indicator will emit red color when the switch
is pressed.
Use caution for long runtimes at high level and turbo as flashlight may get
hot.
Three batteries are parallelly connected inside the flashlight, either 1 or 2
or 3 batteries are able to turn the flashlight on,it is better not to use Turbo
when using 1 or 2 batteries, it may cause to suddenly shut down due to
battery protection.
Please choose 5V 2.1A USB power supp ly or higher rate power supply to
charge the flashlight.
S
ide
switch
Charge indicator /
Low voltage indicator
Micro-USB
Charging Port
Output
