Congratulations
on your purchase of the
Olympia AD220 Cree XPG LED
high-performance
flashlight. This product is designed to provide you
with the best possible functionality. The AD220
utilizes Cree
®
LED technology that is geared for
optimum brightness and efficiency. It’s constructed
in aircraft-grade aluminum with premium Type II
hard anodized, anti-abrasive finish. The lightweight,
compact design makes it a functional light for
multiple uses including hunting, hiking, camping,
caving, general household use, recreational
activities, rugged sports or emergency situations.
Please take a few moments to read this user guide
to ensure that you get the best performance and
years of trouble-free service.
Product Description
Battery Installation
1. Unscrew the tail switch cap and insert
2xCR123 (NiMH) rechargeable *batteries. The
(+) terminal on the batteries should face toward
the flashlight’s head.
2. Replace the tail switch cap and be sure to
tighten snugly, but do not over tighten as this
could strip the threads in the cap. Turn on the
flashlight as indicated in any of the options
listed in the table that follows.
Note: If the tail
cap is not tightened snugly; the flashlight
will not turn on.
3. When the battery life is nearly depleted, your
flashlight will blink to indicate new batteries are
needed.
*batteries included
Flashlight Operation
Your
Olympia AD220 Cree XPG LED
high-
performance flashlight has a push-button tail
switch for on/off operation and is equipped with
1) Momentary and 2) Continuous light options.
It also has 5 light modes to suit your varied
needs. See table instructions to access these
functionalities:
Olympia AD220
Cree XPG LED
Flashlight
User Guide
Lighting Operation Modes
Momentary-on
Lighting
Press the push-button tail switch
half-way to activate the light
momentarily.
Continuous
Lighting
Press the tail switch push-button to
completely turn on the flashlight.
The light will stay on until the push-
button is turned off.
Lighting Modes
There are five types of light output:
High
Middle
Low
Strobe
SOS
Press the tail push-button to switch
to each mode
Accessing the 5 Lighting Modes
High Beam
Press the push-button tail
switch once
Mid Beam
Press the push-button tail
switch twice
Low Beam
Press the push-button tail
switch 3 times
Strobe
Press the push-button tail
switch 4 times
SOS
Press the push-button tail
switch 5 times
Memory function
Your
Olympia AD220 Cree XPG LED
flashlight
automatically memorizes the last light setting/
mode used when the flashlight next is turned
on. i.e., after being in any one of the five light
settings (High
Middle
Low
Strobe
SOS) for
3 seconds, the last one used will be memorized.
Maintenance and Precautions
1. Do not disassemble the sealed head. Doing
so can cause damage to the flashlight and will
void the warranty.
2. Use high-quality batteries or you run the risk
of the flashlight being damaged by electrolyte
leakage or battery breakage.
3. If the flashlight will not be used for a long time,
remove the batteries to avoid damage caused
from battery leakage.
4. Lubricate the O-rings regularly using a
Q-tip
®
. Apply a small dab of silicone grease
or petroleum jelly to the contacts to prevent
corrosion. Doing so will keep the flashlight
properly sealed against water. If the O-rings are
damaged after prolonged use, replace them.
5. Clean the flashlight contacts periodically
especially if the light flickers or does not light
up. There are different reasons for a flickering or
non-working light:
A: The batteries may need to be replaced.
Solution: Replace old/defective batteries with
new ones (be sure to double check correct
installation of + and - terminals).
B: The threads, PCB board contact or other
contacts are dirty.
Solution: Use a Q-tip
®
to apply a tiny amount
of alcohol to clean the contact points.
If the above methods do not work, please refer to
the warranty policy listed in this user guide.
Warning
The AD220 is a high-intensity lighting device and
capable of causing eye damage. Please avoid
shining the light directly into the eyes.
!
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
Clip
Tail
Cap
Switch
Lanyard
Hole
Body
Head
