background image

COPYRIGHT  2007: OMEGA RESEARCH & DEVELOPMENT, INC.

Crime Guard

       850i

5

OPERATION  MANUAL

FRONT  COVER

PRINTER’S NOTE:

production front cover

is color; this is a

place marker cover.

Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT,
INC. (the "Company"), are warranted to be free from defects in materials and
workmanship under normal use.  If a product sold by the Company proves to be
defective, the Company will repair or replace it free of charge within the first year
and  thereafter all parts to be repaired will be free with only a nominal charge for
Omega's labor and return shipping, to the original owner during the lifetime of the
car in which it was originally installed.

All products for warranty repair must be sent postage prepaid to Omega

Research & Development, Inc., P.O. Box 508, Douglasville, Georgia 30133, or
send via UPS to:  981 N. Burnt Hickory Rd., Douglasville, Georgia 30134, with
bill of sale or other dated proof of purchase. This warranty is nontransferable and
does not apply to any product damaged by accident, physical or electrical misuse
or abuse, improper installation, alteration, any use contrary to its intended
function, unauthorized service, fire, flood, lightning, or other acts of God.

This warranty limits the Company's liability to the repair or replacement of

the product. The Company shall not be responsible for removal and/or reinstallation
charges, damage to or theft of the vehicle or its contents, or any incidental or
consequential damages caused by any failure or alleged failure of the product to
function properly. UNDER NO CIRCUMSTANCES SHOULD THIS
WARRANTY, OR THE PRODUCT COVERED BY IT, BE CONSTRUED
AS A GUARANTEE OR INSURANCE POLICY AGAINST LOSS.
 The
Company neither assumes nor authorizes any person or organization to make any
warranties or assume any liability in connection with the sale, installation, or use
of this product.

This device complies with F.C.C Rules part 15. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference
and, (2) This device must accept any interference that may be received, including
interference that may cause undesired operation.
 The manufacturer is not responsible for any radio TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.

L I M I T E D     L I F E T I M E     W A R R A N T Y

Omega Research and Development, Inc.

P. O. Box 508

Douglasville, Georgia    30133

www.caralarm.com

03/07   MO-CG 850i5   REV1

BACK  COVER

PRINTER’S NOTE:

production back cover

is color; this is a

place marker cover.

Summary of Contents for Crime Guard 850i5























Reviews: