OMNI Tx-5.10
DCC
Programmable 2.4GHz Transmitter
For simultaneous control of up to
10 models and 24 functions on
each model.
P.O.Box 675,
Blackburn, Lancs.
BB2 9QJ
UK
WWW.FOSWORKS.CO.UK
Tel 01254 814675
Rx
-
24 receiver circuit diagram showing optional use of ESC. Note that stand-
ard Rx24 do not have the ESC connection, Rx24
-
ESC must be ordered spe-
cially. There are several versions including Drivelock on F8.
The programmable
OMNI Tx
-
5.10
handheld transmitter will control your garden railway
electric locomotives perfectly from the palm of your hand. An
Omni FRx
-
24
receiver with
be needed to work with the
OMNI Tx
-
5.10
transmitter in DCC mode, but the Tx5.10 will
also operate our standard r/c Rx22 receivers in analogue DC models.
2.4GHz gives glitch free control for up to 800 metres range with no
obstructions.
The Regulator Knob controls speed and direction. Forwards to the right, reverse to the
left. Cruise control is possible by turning off the transmitter while the train is running.
Turn back on to instantly regain control.
OMNI Tx-5.10
DCC
2.4GHz Handheld Transmitter
2 x AAA Battery box
FUNCTION
1.2.3 /
4.5.6 /
7.8.9 /
10.11.12
Buttons
13.14.15/
16.17.18 /
19.20.21/
22.23.24
Buttons 1.2.and 3 in conjunction with
RED
and
GREEN
Operate DCC command functions
These buttons are also used to re
-
program a receiver.
Functions
4,5
,and
6
are operated by holding the
green
shift button first, buttons
7,8
and
9
by holding the
red
shift button first and functions
10,11
and
12
by holding down
both
shift
buttons whilst pressing the function button required., likewise for functions 13
-
24.
ON/OFF
Slide Switch
Slide down for ON
If Alkaline batteries are used up to 100 hours of continuous
use is possible
10 way Selector
Knob
Use it in combination
with Channel switch to
move between models,
then press
RED
button
to acknowledge, once
you
have
checked
speed setting.
Regulator Knob Forwards and backwards with centre stop.
Toggle switch allows
function range
to be selected and the se-
lector knob allows simultaneous control of up to 10 models.
24 functions
for
DCC
operation
2.4GHz Technology by Timpdon Electronics
With
E
mergency stop function
Requires an
OMNI Rx24
receiver with DCC interface module or OMNI
Rx22 or Rx2 with optional MCS switchers for analogue DC operation
Shift Buttons
Green
and
Red
Enable F4 to F12 in com-
bination with black but-
tons. E.g.
F7
is obtained
by pressing and holding
the
RED
button then
pressing BLACK button
F1. Hold both down to
obtain F10, F11 and F12.
LED’s 1 & 2
Indication of battery
and radio status plus
indications during bind
and calibration.
Regulator Knob
Turn right for forwards
and left for reverse. The
further you turn, the fast-
er the loco goes.
Centre Stop.
Whilst moving, if a quick
stop is needed, move the
knob fully to the opposite
direction for an
E
-
stop
This stops ALL active
models.
This knob is also used
when reprogramming the
top buttons.
Selector
Switch to change be-
tween
functions 1
-
12
and 13
-
24
