SUITABILITY FOR USE
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the
Product in the Buyer's application or use of the Product. At Buyer's request, Omron will provide applicable third party certification documents
identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the
suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for
determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer shall take application
responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT
THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY
RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Regional Headquarters
OMRON ELECTRONICS B.V.
Wegalaan 67-69, 2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-400/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
Industrial Automation Company
OMRON Corporation
Kyoto, JAPAN
Contact: www.ia.omron.com
In the interest of product improvement, specifications are subject to change without notice.
OMRON ELECTRONICS Pte. Ltd.(OEP-SG)
438A Alexandra Road # 05-05/08
Alexandra Technopark, Singapore 119967
Tel: (65) 6547-6789/Fax: (65) 6547-6769
Removing the draw-out jig when only one hook is caught in the draw-out jig insertion hole
(This procedure is the same for the Y92F-55, Y92F-58, and Y92F-59.)
1
Draw out the interior body from the rear case.
Y92F-55 (for G size:48
h
24
PP
)
Y92F-58 (for C size
48
h
48
PP
) or Y92F-59 (for E size:48
h
96
PP
or A size:96
h
96
PP
)
(1) Slowly insert the Draw-out Jig into the Draw-out Jig insertion holes
laterally until it clicks into place. (There is a hole at both the top and
bottom.) (If you attempt to draw out the interior body of the Digital
Controller when only one hook is engaged, the Digital Controller may be
damaged.)
(2) Pull out the Draw-out Jig together with the front panel. Do not pull
with excessive force. Slowly pull out the Digital Controller laterally. (If
you pull the interior body out at an angle, the Digital Controller may
be damaged.)
(3) After the interior body is free from the rear case, support the interior
body with one hand and draw it out slowly in a horizontal direction.
2
Prepare the new interior body.
(1) Place the Digital Controller flat on a table and slowly insert the
Draw-out Jig into the Draw-out Jig insertion holes laterally until it
clicks into place. (There is a hole at both the top and bottom.)
(The E5CC-D is shown in the figure.)
(2) Place the Digital Controller on a table facing upward.
(3) Hold the rear case with your hand and slowly draw out the interior
body in a vertical direction. If you draw out the interior body
horizontally while holding the Digital Controller in your hand, the
interior body will fall and may be damaged.
3
Insert the new interior body into the rear case.
(1) When inserting the interior body back into the rear case, make
sure the PCBs are parallel to each other, mount the sealing
rubber, and press the interior body toward the rear case and into
position, making sure that the sealing rubber does not move.
(2) When you press the Digital Controller into position, press down
on the rear case hooks so that the case hooks securely lock in
place. (There are rear case hooks at both the top and bottom of
the rear case.) If the Digital Controller is not correctly mounted
into the rear case, the rear case may not be waterproof. When
inserting the Digital Controller, do not allow the electronic
components to touch the rear case. (The E5CC-D is shown in the
figure.)
(1) Align the arms on the Draw-out Jig with the top of the front panel on
the Digital Controller and position it vertically.
(The Y92F-58 is shown in the figure.)
(2) Align the hooks on the Draw-out Jig with the Draw-out Jig insertion
holes on the Digital Controller and slowly insert the Draw-out Jig into
the Draw-out Jig insertion holes laterally until it clicks into place. (If
you attempt to draw out the interior body of the Digital Controller
when only one hook is engaged, the Digital Controller may be
damaged.)
(The Y92F-58 is shown in the figure.)
(3) Pull out the Draw-out Jig together with the front panel. Do not pull
with excessive force. Slowly pull out the Digital Controller laterally. (If
you pull the interior body out at an angle, the Digital Controller may be
damaged.)
(4) After the interior body is free from the rear case, support the interior
body with one hand and pull it out slowly in a horizontal direction.
(1) Pull the Draw-out Jig slowly in the direction shown in the figure.
(This step is the same even if the other hook is caught.)
(2) Confirm that the Draw-out Jig is free of the Draw-out Jig insertion hole.
(3) If the interior body separates from the rear case, slowly press the interior body
into the rear case in a horizontal direction. (The E5CC-D is shown in the figure.)
Draw-out Jigs
Y92F-55, Y92F-58, and Y92F-59
© OMRON Corporation 2015 All Rights Reserved.
0194754-5B (Side-A)
If you do not follow the procedures above, the Digital Controller may be damaged.
INSTRUCTION MANUAL
To ensure safe usage of the product, thoroughly read and understand this Instruction Manual and keep it in a safe location so that it is
available for reference whenever required.
EN
OMRON Corporation
Ɣ
Introduction
Ɣ
Drawing Out the Interior Body of the Digital Controller to Replace It
You can use the Draw-out Jig to remove the interior body of a Digital Controller mounted to a panel from the rear case
to perform maintenance without removing the terminal leads. You can also use the Draw-out Jig to remove the interior
body of a Digital Controller that is not yet mounted. These Draw-out Jigs can be used for draw-out-type E5
ȏ
C,E5
ȏ
D
The Digital Controller consists of an interior body and a rear case.Turn OFF the power supply before you attempt to
remove the interior body of the Digital Controller, and never touch nor apply shock to the terminals or electric
components.If the terminals are corroded, replace the rear case as well.
Sealing rubber position
Case hooks
(1)
(1)
(2)
(1)
(1)
(2)
(2)
(3)
(2)
(2)
(2)
(3)
(1)
(1)
(2)
(1)
(3)
Top View
Rear case hooks
PCBs
Keep the PCBs parallel
to each other and inset
them into the rear case.
Rear case hooks
Hook
Draw-out Jig insertion holes
Draw-out Jig
Front panel
Rear case
Draw-out Jig insertion holes
Rear case
Draw-out Jig insertion holes
Front panel
Arm
Draw-out Jig insertion holes
Align the arms
with the front
panel.
Fax: (1) 847-843-8568/7787
