Direct Set-Up
To set up the ZAPPER for your Television follow the instructions below.
To set up your Television:
Turn on your Television.
Find your Television code in the Set-Up Code
section (see reverse). Codes are listed by brand
name. The most popular codes are listed first.
Press and hold the
MAGIC key until the light
blinks twice
(the light will blink once then
twice).
Enter your 5-digit code
according to the
chart below. The red light will blink twice.
=
1
Volume -
=
2
Pro
=
3
Programme -
=
4
Now, aim the ZAPPER at your Television and press
POWER
. If your Television switches off, your
ZAPPER should be ready to operate your device.
Turn your device back on and try all the remote’s functions to
ensure they are working properly. If the functions do not work
properly, repeat steps 1-6 using another code listed under your
brand.
Important notes:
- Some codes are quite similar. If your television does not respond or is
not functioning properly with one of the codes, follow steps 1-6 with
each code listed for your brand.
- If none of the codes listed for your brand operate your television,
follow the Search Method described in the next section. The Search
Method can be used even if your brand is not listed at all.
- Write the code for your TV in the boxes provided below and
inside the battery compartment for easy future reference.
TV Code
Searching for Your Code
If your Television does not respond to the ZAPPER after trying all the
codes listed for your brand, try searching for your code. To search for
your TV code:
Turn on your TV and aim your ONE FOR ALL at your television.
Press and hold the
MAGIC key until the light
blinks twice
(the light will blink once then
twice).
Next, press the
Programme(-) key three times.
Next, alternate between
Programme(-)
and
POWER
until your Television turns off. You may
have to press these keys many times, so be
patient. Remember, you must aim the ZAPPER at
your device the entire time you are searching for
your code.
When your device turns off, press and release
MAGIC
. Don’t forget, press MAGIC as soon as
your device turns off.
The ZAPPER should now be ready to operate your Television.
Turn your device back on and try all the remote’s functions to
ensure they are working properly. If some of the ZAPPER’S
commands are not operating correctly, try the search method
again, you may be using the wrong code.
Important notes:
During step 4, you may have to press these keys many
times (up to 150!), so be patient. Remember, you must aim the ZAPPER at
your device the entire time you are searching for your code.
Code Blink Out
After you have used the Search Method, you can find out which
code the ZAPPER responded to by blinking back the code. It’s handy
to know your Television code for future reference. Remember, you
can only blink back your code after the ZAPPER is operating your
device.
To blink out your TV code:
Press and hold the
MAGIC key until the light
blinks twice
(the light will blink once then
twice).
Next, press
Programme(-), Programme(-),
Pro)
.
For the first digit of your 5-digit code, press
(
)
and count the red blinks.
For the second digit, press
Volume - ( )
and
count the red blinks.
For the third digit, press
Pro)
and
count the red blinks.
For the fourth digit, press
Programme(-)
and
count the red blinks.
For the fifth digit, press
MUTE
and count the
red blinks.
Now you have your 5-digit code. Write your
code in the boxes provided previously for easy,
future reference.
Controlling Colour & Brightness
Depending on the functions of your original remote control, the
ZAPPER can operate the colour and brightness settings of your
Television.
Scan
Your ZAPPER comes with a special Scan function which lets you
“scan” through every programme available on your TV.
To scan the programmes on your TV:
Aim the ZAPPER at your TV.
Press and release
MAGIC
then press the
MUTE
key.
The ZAPPER will send the command to advance
through all the programmes available on your
Television stopping at each programme for
about three seconds. Remember, you must aim
the ZAPPER at your device the entire time you
are using scan.
When you find a programme you would like to
watch, simply press the ( ) on the
ZAPPER keypad to stop the Scan feature.
Important notes:
- Scan may not function with television that did not
have a pro/- key on the original remote.
U S E R G U I D E & C O D E B O O K
Universal Remote
R
R e t a i n F o r F u t u r e R e f e r e n c e
URC-6510
700927
Thank you for purchasing the ZAPPER universal remote control
(URC-6510). Your ZAPPER package contains:
The ZAPPER Remote Control
The ZAPPER User Guide & Code Book
The User Guide & Code Book explains in simple steps how to set up
and operate your new universal remote control.
You may need this
guide again in the future, so please be sure to keep it.
Your ZAPPER needs 2 new “AAA/LRO3” batteries.
Your ZAPPER is designed to let you use one remote to operate your
Television. The illustration on the left and the chart below describe
the features and functions of the ZAPPER universal remote control.
Features and Functions
Key
Function
LED
LED
The LED (Light Emitting Diode) flashes red to show
the remote is working.
MAGIC
The MAGIC key is used to set up your ZAPPER and to
access special features.
Power
The Power key turns your devices both on and off.
Mute
The Mute key operates the same function it did on
your orginal remote control. It is also used to activate
the Scan feature (see Scan).
/-, Pro/-
The Volume and Programme keys control the two most
frequently used functions of your devices. They
operate just as those on your original remote control.
These keys are also used to program the ZAPPER for
your devices and to control the Colour and Brightness
settings of your television (Advanced Operation).
The ZAPPER needs 2 new “AAA/LRO3” alkaline batteries.
Remove the battery cover from the back of
the ZAPPER by pressing down on the tab.
Match the batteries to the +/- marks inside
the battery case, then insert the batteries.
Press the battery cover back into place.
Important notes:
- In order to avoid having to reprogram your ZAPPER after you remove
the batteries, you will need to insert new batteries within 5 minutes.
- Also, it is best that you do not use rechargeable batteries.
- On the inside of the battery compartment door you will find a
label on which to write your set-up code after your ZAPPER is set
up for your television. Please write down your code for easy,
future reference.
ABOUT YOUR ZAPPER
Features and Functions
Front Page
INSTALLING THE BATTERIES
Front Page
SETTING UP THE ZAPPER
Front Page
Direct Set-Up
Front Page
Search Method
Front Page
ADVANCED OPERATION
Controlling Colour & Brightness
Front Page
Scan
Front Page
TROUBLE-SHOOTING
Helpful Hints
Front Page
Consumer Help-Line
Front Page
SET-UP CODES
Back Page
Quick Set-Up
Back Page
Codes
Back Page
Setting Up The ZAPPER
1
2
3
4
ONE FOR ALL
Acura
Admiral
Adyson
Agazi
AGB
Aiko
11132
12224 12242 23313
14232
21131
31121
14231 11132 11322
22414 11314 12131
22332 13444
1
2
3
5
6
4
1
2
3
4
5
6
7
Installing The Batteries
1
2
3
Contents
About Your ZAPPER
UK
5
6
x3
If you have any questions about the operation of your new ONE
FOR ALL Universal Remote Control, you may call our consumer help-
line for assistance. Before calling, please read this manual carefully
to find the answer to your question. If you cannot find a solution in
this manual, we ask that you complete the chart below on your
television before calling.
Please ensure you have this
information ready upon speaking to our customer service
department even if done via fax or e-mail.
In the UK:
phone: 0800 966 194
fax: +31 53 432 9816
e-mail: ofahelp@ueic.com
Hours: 9 am - 7 pm Mon-Fri / 9 am - 3 pm Sat
In Ireland:
phone: 1-800 553 118
fax: +31 53 432 9816
e-mail: ofahelp@ueic.com
Hours: 9 am - 7 pm Mon-Fri / 9 am - 3 pm Sat
In Australia:
phone: 1-800 064 472
e-mail: ofahelp@ueic.com
We need to know:
- Your ONE FOR ALL model number: URC-6510
- Date of purchase:
day
/
month
/
year
day/month/year
- Your Television:
(The first row is an example of how to complete this table)
TYPE
BRAND
MODEL NR.
REMOTE
OFA CODE
MODEL NR.
TV
Sony
KVX-2950B
RMT-V131B
11133
Type numbers can be found in your equipment’s owner’s
manual, on the front of the device or on the factory plate
behind the device.
Solution:
Replace batteries with 2 new
“AAA/LR03” alkaline batteries
Make sure you are using new
batteries and are aiming the ONE
FOR ALL at your device.
A) Try all the codes listed for your
brand. B) Try the search method.
Try the search method.
You may be using the wrong code.
Try Direct Set-Up again trying each
code listed under your brand or
start the search method over again
to locate the proper code.
Press MAGIC until the light blinks
twice.
Then press:
(Programme-)
(Pr)
(Programme-)
If your original remote did not
have c/- keys, the Zapper
may not operate this function.
Problem:
Red light does not blink
when you press a key?
The ONE FOR ALL does not
respond after pressing a
key?
The ONE FOR ALL does not
operate your television?
Your brand is not listed in
the ONE FOR ALL code section?
The ONE FOR ALL is not
performing commands
properly?
Your TV switches to
programme 1 when you
press the power key before
switching off OR you must
press Power twice to switch
on your TV?
You cannot reach channel 10
and above on your TV.
Trouble-Shooting
Helpful Hints
1
Advanced Operation
2
■
■ ■
■ ■
■ ■
■ ■
■
then hold
Press
Colour up =
then hold
Press
Colour down =
then hold
Press
Brightness up =
then hold
Press
Brightness down) =
MAGIC
Pro
Power
Volume
-
Programme
-
Mute/Scan
