background image

 

ON Series m UPS

 

ON Series m UPS User Instruction Manual

1

 

ON Series m 
UPS

 

Please read and save these instructions. This manual 
contains important instructions for the ON Series m 
UPS family. Follow these instructions during the 
unpacking, installation and maintenance of the 
Uninterruptible Power Supply (UPS) and batteries. 
If you have a problem with the UPS, please refer to 
this manual before calling Technical Services. The 
Troubleshooting Section starting on page 16 
addresses most UPS-related issues.

 

Introduction

 

Thank you for selecting this uninterruptible power 
supply (UPS). ONEAC’s ON Series offers the most 
reliable protection from the harmful effects of 
electrical line disturbances for your computing and 
communications equipment. ONEAC’s ISO 9001 
certification represents our commitment to building 
world-class products. We take pride in every unit that 
leaves our manufacturing facility

 

Technical 
Support

 

ONEAC

 

®

 

 offers 24-hour technical support. To 

contact ONEAC Technical Services: 

• North America: (800) 327-8801 (opt. 3) or 

(847) 816-6000 (opt. 3)

• Europe: +44 (0) 2380 610311
• email: ts@oneac.com.

 

NOTE: 

 

All calls received before 7 a.m. or after 7p.m. 

Central Standard Time are forwarded to a cell 
phone. An ONEAC Technical Support Representative 
will return your call within one half hour between 5 
p.m. and 10 p.m. Central Standard Time. Except for 
emergencies, calls received between 10 p.m. and 7 
a.m. will be returned during normal business hours.

 

Please check with ONEAC Technical Services 
before attempting to repair or return any ONEAC 
product. If an ONEAC unit needs repair or 
replacement, ONEAC Technical Services issues a 
Return Material Authorization (RMA) number along 
with instructions on how to return the unit.

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for ON Series


























Reviews: