background image

 

ONEAC Sinergy UPS User Manual

i

 

Sinergy™ Series User Instruction Manual

 

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

 

Please read and save these instructions. This manual contains important instructions for ONEAC models: 

• S700A

• S1000XA

• S2000XA

• S3000XA

• SBP1000

• SBP3000

 Follow these instructions during installation and maintenance of the UPS and batteries. 

If you have a problem with the UPS, please refer to this manual before calling the Technical Support 
Department. The Troubleshooting section on page 28 addresses most UPS-related issues. 

 

FCC Compliance

 

ATTENTION: 

 

Changes or modifications to this unit not expressly approved by the party responsible or in FCC 

compliance could void the user’s authority to operate the equipment.

 

This equipment was tested and complies with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These 
limits are designed to provide reasonable protection against harmful interference when the UPS is operating in a commercial 
environment. The UPS generates, uses, and can radiate radio frequency energy. If installation and use is not in accordance 
with the instruction manual, it may cause harmful interference to radio communications. 

 

ATTENTION:

 

Operation of this equipment in a residential area may cause harmful radio communications 

interference. The user is responsible for correcting the interference. 

 

913-459 Rev. D1  

 

ONEAC USA
27944 North Bradley Road
Libertyville, IL 60048-9700
USA
Telephone: (847) 816-6000 
Toll Free: (800) 327-8801
Facsimile: (847) 680-5124

ONEAC EUROPE
George Curl Way
Southampton, Hampshire SO18 2RY
United Kingdom
Telephone: +44 (0) 2380 610311
Facsimile:  +44 (0) 2380 612039 

 

• S700A-RM

• S1000XA-RM

• S2000XA-RM

• S3000XA-RM

• SBP1000-RM

• SBP3000-RM

• SE61XA (SE41XA)

• SE101XA (SE81XA)

• SE203XA (SE153XA)

• SBPE61

• SBPE101

Summary of Contents for S1000XA



















































Reviews: