Optex ELITE PRO Instruction Manual Download | Manualshive

Page: 1 / 24

background image

Preface

Installation

Troubleshooting

Specifications

5932260 2022.08

ELITE PRO

ELITE PRO2

ELITE PRO LE

Sensors for full-energy and low-energy automatic swing doors

Packaged combinations of
Swing Door Sensor Head

OA-607 T

Swing Door Sensor Controller

OC-907C T

Instruction Manual

Manufacturer’s statement

Read this operation manual carefully before use, to ensure proper operation of this product.
Failure to read this operation manual may cause improper operation and may result in serious injury or death of a person.
The meanings of the symbols are as follows.

WARNING

WARNING

Failure to follow the instructions provided with this indication and improper handling may cause injury and/or
property damage.

CAUTION

CAUTION

Failure to follow the instructions provided with this indication and improper handling may cause death or serious
injury.

NOTE

NOTE

Special attention is required to the section of this symbol.

1. Set door speeds and verify proper operation of door manufacturer’s equipment prior to applying power to the sensor system.
2. Do not install the sensor where it might be directly sprayed with rainwater.
3. Verify proper wiring prior to applying power to the sensor system to prevent damage to equipment.

4. When setting the sensor’s area pattern, make sure there is no traffic around the installation site.

5. Do not attempt to rebuild or repair sensor heads or control unit. Contact the address in this manual for replacement products.

6. Only use the sensor as specified in the supplied instructions.

7. Walk test the installation to verify operation is in compliance with all local laws, codes and standards of your country.
8. Upon completion of installation and adjustments, instruct the owner/operator on proper operation of the door and sensor system.

9. Identify any switches/breakers that will place the door out of service when unsafe or improper operation is identified.

Contents

Manufacturer’s statement .........................................................................1
Overview ...................................................................................................2
Accessories ...............................................................................................2
Part names ................................................................................................4
Installation .................................................................................................5
Wiring ......................................................................................................10
Power on .................................................................................................13

Indicator confirmation

..............................................................................13

Function settings .....................................................................................15
Detection area adjustment ......................................................................17
Automatic settings and auto area learn ...................................................18
Walk test .................................................................................................19
Inform building owner/operator of the following items .............................19
Troubleshooting.......................................................................................19
Dimensions .............................................................................................23

..........................................................................................24

1
2
3
...
»

Summary of Contents for ELITE PRO

























Reviews:

No comments

Related manuals for ELITE PRO

RIRS 2500VE EKO 3.0

Brand: Salda Pages: 58

Brand: SWF Pages: 15

Aristo RoboFeed 30-4

Brand: ESAB Pages: 34

Brand: Fronius Pages: 92

Brand: Command access Pages: 12

Brand: G-U Pages: 20

Brand: AMH Pages: 22

Brand: Lincar Pages: 64

Brand: GÜDE Pages: 60

Rogue ES 180i Pro

Brand: ESAB Pages: 22

Brand: Dexter Power Pages: 8

Brand: Melu Pages: 4

Brand: Pamex Pages: 18

Brand: quadient Pages: 2

Brand: quadient Pages: 2

Brand: quadient Pages: 18

Brand: quadient Pages: 26

Brand: quadient Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands