READ ALL INSTRUCTIONS
PRIOR TO INSTALLATION
Set the Pattern
Before Installation
The Voyager can be set to rotate
between 40° and 360° (preset at 180°)
1. Turn the top of the head all the
way to the left until it stops and
then all the way to the right. This
is the starting point for the rotation
(Figure 1).
2. Insert a flat bladed screwdriver
into the pattern adjustment screw
(Figure 2).
3. Turn clockwise to increase rota-
tion; counterclockwise to decrease
rotation. Each full turn increases/
decreases rotation by 90˚.
Head Installation
1. Flush sprinkler lines.
2. Thread the sprinkler onto a riser
and set the head flush with the
finished turf height (Figure 3).
Note:
DO NOT use pipe dope on the
threads. If necessary, use thread
seal tape.
3. Unscrew the cap and remove the
sprinkler stem from the canister—
be careful of debris falling in canis-
ter.
4. Position the sprinkler stem so that
the arrow points to the right edge
of the rotation.
5. Slide the sprinkler stem back into
the canister and tighten the cap.
Set the Spray Distance
After Installation
Set with water on under system’s nor-
mal operating pressure.
Note:
Preinstalled nozzle (# 7) adjusts
from 25 ft. to 45 ft. depending on sys-
tem water pressure.
1. Insert a small flat bladed screw-
driver key into the distance adjust-
ment slot (Figure 2).
2. Turn clockwise to decrease
distance; counterclockwise to
increase distance.
Caution:
DO NOT turn the adjust-
ment screw too far in either
direction—screw may come free
of threads.
Replace the Nozzle
See Nozzle Specs for other distance
ranges and replace the nozzle if
needed.
1. To access to the nozzle, insert a
flat blade screwdriver into the lift-
ing socket and lift upward (Figure
4)
2. Firmly grip the sprinkler stem—
Note:
the spring inside the canister
is very strong.
3. Insert a small flat bladed screw-
driver into the distance adjustment
slot..
4. Turn the screw counterclockwise
until it is just clear of the nozzle.
Caution:
DO NOT turn the adjust-
ment screw too far in either
direction—screw may come free
of threads.
5. Use pliers to grip the “ears” of the
nozzle and pull it out.
6. Insert the replacement nozzle with
the ears on top and turn the screw
back into place (Figure 5).
7. Adjust distance if necessary (see
Set the Spray Distance).
Clean the Filter
1. Remove grass and dirt around the
sprinkler head so you can see the
top 1 ½ in.
2. Unscrew the cap and remove the
stem assembly.
3. Use pliers to extract the filter from
the bottom of the stem assembly.
4. Clean out debris and replace filter.
5. Replace the stem assembly to the
sprinkler body and screw tightly.
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
proof no:
8
date:
10.02.08
des:
SM
spck:
XX
job no:
NA
client:
Orbit
sku:
55461
upc:
NA
file name:
55461-24 rB.indd
software:
InDesign CS3
colors
additional instructions:
· Translation Proofing code: LB403717
·
color
non printing
PMS
????
PMS
????
color
non printing
PMS
????
Registration
K
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
dimensions:
flat: w: 11.25" h: 5.5"
finished (folded): w 3.75" d: 0" h 5.5"
© 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Voyager
®
gear DriVe
Sprinkler
Aspersor de
trAnsmisión por
engrAnAjes VoyAger
®
Orbit
®
Irrigation Products, Inc.
North Salt Lake, Utah 84054 USA
1-800-488-6156
www.orbitonline.com
© 2008 Orbit
®
Irrigation Products, Inc.
All rights reserved. All trade names are registered
trademarks of respective manufacturers listed.
ENGLISH
Figure 1
Figure 4
Figure 3
Orbit
®
Figure 2
Pattern
adjustment
slot
Distance
adjustment
slot
Figure 5
PN 55461-24 Rev B
CAUTION
n
For outdoor use with cold water only.
n
Do not spray near electrical
connections.
CUSTOMER SERVICE
1-800-488-6156
www.orbitonline.com
No Special Key Required
No se requiere llave especial
