HM-9189-
5
OPERATING MANUAL
World
K
Series
Terminal Box Type
Induction Motors and Reversible Motors
1
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety
precautions.
・
Please read it thoroughly to ensure safe operation.
・
Always keep the manual where it is readily available.
Before using the motor
Introduction
Only qualified personnel should work with the product.
Use the product correctly after thoroughly reading the section “Safety
precautions”.
Should you require the inspection or repair of internal parts, contact the
Oriental Motor office where you purchased the product.
The product described in this manual has been designed and manufactured
for use in general industrial machinery, and must not be used for any other
purpose. Oriental Motor Co., Ltd. is not responsible for any damage
caused through failure to observe this warning.
Standard and CE marking
Motors (except for
5IK90GU-SWT
,
5IK90A-SWT
,
5IK150A-TWT
) are
recognized by UL and certified by VDE.
Recognized name and certified name are motor model name.
The certificate by VDE is valid only for the motor assembly itself. The
capacitor is not included in the certificate.
However, both the motor assembly and capacitor combined have been
tested against and have passed EN 60950-1 Annex B.8.
5IK90GU-SWT
and
5IK90A-SWT
are recognized by UL and certified by
DEMKO.
Voluntary display of the CE mark conforming to the Low Voltage
Directives.
●
Standards
UL 1004-1, UL 1004-2, UL 1004-3
CSA C22.2 No.100, CSA C22.2 No.77, EN 60950-1
Standards File No.
UL File No. E64199 (6 W type), E64197 (25 to 150 W type),
VDE, DEMKO
●
Applications for standard
EN 60034-1, EN 60034-5, EN 60664-1, EN 60950-1
A Running Heating Test and a Locked-Rotor Test has been conducted
with a aluminum radiation plate of size indicated below. For the motor
with a gear head, tests has been conducted with a gear head instead of the
radiation plate.
First number in
motor name
Size [mm (in.)]
Thickness
[mm (in.)]
Material
2
115 × 115 (4.53 × 4.53)
4
135 × 135 (5.31 × 5.31)
5 (40 W)
165 × 165 (6.50 × 6.50)
5 (60 W, 90W,
150 W)
200 × 200 (7.87 × 7.87)
5 (0.20)
Aluminium
●
Installation conditions
Overvoltage category II, Pollution degree 2, Class I equipment (For EN
standards)
When the machinery to which the motor is mounted requires overvoltage
category III and pollution degree 3 specifications, install the motor in a
cabinet that comply with IP54 and connect to power supply via an
isolation transformer.
●
Standards for accessories
Capacitor : UL File No. E83671 (CYWT2), VDE License No. 114747
(for only capacitor rated voltage 450 VAC types)
Capacitor cap : UL File No. E56078 (YDTU2)
Electrical appliance and material safety law
The three-phase round shaft motor type bears a
mark.
Safety precautions
The precautions described below are intended to prevent danger or injury
to the user and other personnel through safe, correct use of the product.
Use the product only after carefully reading and fully understanding these
instructions.
Handling the product without observing the instructions
that accompany a “Warning” symbol may result in
serious injury or death.
Handling the product without observing the instructions
that accompany a “Caution” symbol may result in injury
or property damage.
Note
The items under this heading contain important handling
instructions that the user should observe to ensure safe
use of the product.
•
Do not use the product in explosive or corrosive environments, in
the presence of flammable gases, locations subjected to
splashing water, or near combustibles. Doing so may result in fire,
electric shock or injury.
•
Assign qualified personnel the task of installing, wiring, operating/
controlling, inspecting and troubleshooting the product. Failure to
do so may result in fire, electric shock or injury.
•
Do not transport, install the product, perform connections or
inspections when the power is on. Always turn the power off
before carrying out these operations. Failure to do so may result
in electric shock.
•
Turn off the power in the event the overheat protection device
(thermal protector) is triggered. Failure to do so may result in
injury or damage to equipment, since the motor will start abruptly
when the overheat protection device (thermal protector) is
automatically reset.
•
The motor is Class
I
equipment. Install the motor so as to avoid
contact with hands, or ground it to prevent the risk of electric
shock. If the motor has a protective ground terminal, be sure to
connect the terminal to the ground.
Dieser Motor ist in Geräten mit Schutzklasse I zu verwenden. Der
Motor ist so einzusetzen, dass er nicht berührt werden kann, bzw. er ist
zu erden, um Stromschläge zu verhindern. Wenn der Motor über eine
Schutzerdungsklemme verfügt, ist die Erdung über diese vorzunehmen.
•
Install the motor in an enclosures in order to prevent electric
shock or injury.
•
Keep the input-power voltage within the specification to avoid fire
and electric shock.
•
Connect the cables securely according to the wiring diagram in
order to prevent fire and electric shock.
•
Do not forcibly bend, pull or pinch the lead wires. Doing so may
result in fire and electric shock.
•
Be sure to insulate the connection terminal of the capacitor.
Failure to do so may result in electric shock.
•
Turn off the power in the event of a power failure, or the motor
will suddenly start when the power is restored and may cause
injury or damage to equipment.
