background image

CEMENT 

MIXER

550W  125L

SPECIFICATIONS

Motor:  

550W

No Load Speed 

2950/min

Drum Speed: 

34/min

Gross Drum Volume: 

125L (4.41 cu ft)

Unmixed Dry Volume: 

100L (3.53 cu ft)

Mixed Wet Volume: 

91L (3.21 cu ft)

Drum Mouth: 

Ø375mm (14 ¾”)

IP Rating: 

 

IP44

Weight:  

48kg

CMX-125U

WHAT’S IN THE BOX

Cement Mixer

Assembly Fasteners

WARRANTY

0616

2
4

2

2

2

6

4

M8    55
M8    65

M8    60

M8    20

M8    20

M8    30

M8    20

1

M10   70

2

10

2

4

M8    16

1

1

2

M8    25

4
4

4

8

OZITO UK

 

Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG

All of our products undergo strict quality checks to ensure that they reach 

you in perfect condition. In the unlikely event that your device develops a 

fault, please contact our service department at the address shown on this 

guarantee card. You can also contact us by telephone using the customer 

service number shown. Please note the following terms under which 

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the 

manufacturer mentioned below promises to buyers of its new products 

in addition to their statutory guarantee claims are not affected by this 

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or 

manufacturing faults on a product which you have bought from the 

manufacturer mentioned below are limited to either the rectification of said 

defects on the product or the replacement of the product, whichever we 

prefer. 

Please note that our devices are not designed for use in commercial, trade 

or professional applications. A guarantee contract will not be created if the 

device has been used by commercial, trade or industrial business or has 

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee: 

- Damage to the device caused by a failure to follow the assembly 

instructions or due to incorrect installation, a failure to follow the operating 

instructions (for example connecting it to an incorrect mains voltage or 

current type) or a failure to follow the maintenance and safety instructions 

or by exposing the device to abnormal environmental conditions or by lack 

of care and maintenance. 

- Damage to the device caused by abuse or incorrect use (for example 

overloading the device or the use or unapproved tools or accessories), 

ingress of foreign bodies into the device (such as sand, stones or dust, 

transport damage), the use of force or damage caused by external forces 

(for example by dropping it). 

- Damage to the device or parts of the device caused by normal or natural 

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original 

date of purchase and is intended for DIY (Do It Yourself) use only. Warranty 

excludes consumable parts. Guarantee claims should be submitted 

before the end of the guarantee period within two weeks of the defect 

being noticed. No guarantee claims will be accepted after the end of the 

guarantee period. The original guarantee period remains applicable to the 

device even if repairs are carried out or parts are replaced. In such cases, 

the work performed or parts fitted will not result in an extension of the 

guarantee period, and no new guarantee will become active for the work 

performed or parts fitted. This also applies if an on-site service is used.

 

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST 

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR 

REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts, 

consumables and missing parts as set out in the service information in 

these operating instructions. 

CUSTOMER SERVICE HELPLINE 

GB: 0151 294 4488 

IRL: 1850 882711 

Ozito-diy.co.uk

ozito-diy.co.uk

ORIGINAL INSTRUCTIONS

Summary of Contents for CMX-125U











Reviews: